American Dryer Corp. AD-840 Скачать руководство пользователя страница 50

Страница: 50 / 64

C. LED Display/Codes

The LED display informs the user of cycle status and program verification and displays important diagnostic

and fault codes.

1. Display Operating Status

a. Cycle in Progress - While the dryer is operating, the display will read which cycle is in progress. For

example, in the drying cycle (mode), the display will read "dr", and in the cool down cycle (mode),

the display will read "CL".

b. Cycle Status - While a cycle is in progress, the display will show the progress of the cycle (load) that

is being processed.

1) Automatic Drying Cycle - The cycle status portion of the display will show the percentage of

extraction.

2) Timed (Manual) Drying Cycle - The cycle status portion of the display will show the drying or

cool down time and will count downward until the programmed time has expired.

c. Alternate Display Programs - Programming allows for the display to read just the cycle in progress

or just the basket temperature or to flash back and forth from cycle in progress to basket temperature

while the dryer cycle is in progress.

d. Indicator Dots - Located at the top of the display is a series of dots which indicate the various

microprocessor controller output functions while a cycle is in progress.

Illus. No. 3 -BLOWER MOTOR INDICATOR -

This indicator dot is on whenever a cycle is in

progress. In addition, when the anti-wrinkle

program is active, this indicator will be on

whenever the microprocessor controller is in

the guard on time program.

Illus No. 4 - HEAT INDICATOR - This indicator

dot is on whenever the microprocessor controller

is calling for the heating unit to be active (on).

1. CYCLE IN PROGRESS

a. dr -- DRYING CYCLE

b. CL -- COOL DOWN CYCLE

2. CYCLE STATUS

a. AUTOMATIC MODE DISPLAYS % OF EXTRACTION

b. MANUAL MODE DISPLAYS DRYING TIME OR COOL DOWN TIME

3. ON INDICATOR, DRYER IS IN OPERATING MODE

4. HEAT ON INDICATOR

5. BASKET IN REVERSE MODE (C.C.W.) INDICATOR

6. BASKET IN FORWARD MODE (C.W.) INDICATOR

Содержание AD-840

































































Результаты поиска

Содержание AD-840

Отзывы:

Похожие инструкции для AD-840

Бренды по названию

Популярные бренды

American Dryer Corp. AD-840, Руководство по обслуживанию

Результаты поиска

Содержание AD-840

Отзывы:

Похожие инструкции для AD-840

Бренды по названию

Популярные бренды