manualshive.com logo in svg

American Dryer Corp. AD-235D, Руководство по установке

Поделиться
Скачать
American Dryer Corp. AD-235D Скачать руководство пользователя страница 25

ON

G.  GAS INFORMATION

It is your responsibility to have 

ALL

 plumbing connections made by a qualified professional to assure that the

gas plumbing installation is adequate and conforms with local and state regulations or codes.  In the absence of
such codes, 

ALL

 plumbing connections, materials, and workmanship 

must conform

 to the applicable requirements

of the National Fuel Gas Code ANSI Z223.1-LATEST EDITION, or in Canada, the Canadian Installation Codes
CAN/CGA-B149.1-M91 (Natural Gas) or CAN/CGA-B149.2-M91 (liquid propane [L.P.] Gas) or LATEST
EDITION.

IMPORTANT:

Failure to comply with these codes or ordinances, and/or the requirements
stipulated in this manual, can result in personal injury and improper
operation of the dryer.

The dryer and its individual shutoff valve 

must be

 disconnected from the gas supply piping system during any

pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPa).

The dryer 

must be

 isolated from the gas supply piping system by closing its individual manual shutoff valve

during any pressure testing of the gas supply system at test pressures equal to or less than 1/2 psig (3.5 kPa).

IMPORTANT:

Failure to isolate or disconnect the dryer from supply as noted can cause
irreparable damage to the gas valve

 

VOIDING THE WARRANTY.

WARNING:  FIRE or EXPLOSION COULD RESULT.

1. Gas Supply

The gas dryer installation 

must meet

 the American National Standard...National Fuel Gas Code ANSI

Z223.1-LATEST EDITION, or in Canada, the Canadian Installation Codes CAN/CGA-B149.1 M91 (Natural
Gas) or CAN/CGA-B149.2-M91 (L.P. Gas) or LATEST EDITION, as well as local codes and ordinances
and 

must be

 done by a qualified professional.

NOTE:

Undersized gas piping will result in ignition problems, slow drying, increased use of
energy, and can create a safety hazard.

The dryer 

must be

 connected to the type of heat/gas indicated on the dryer’s data label. If this information

does not agree with the type of gas available, 

DO NOT

 

operate the dryer

.  

Contact the reseller who sold the

dryer or the 

ADC

 factory.

IMPORTANT:  

Any burner changes or conversions 

must be

 

made by a qualified professional.

The input ratings shown on the dryer’s data label are for elevations up to 2,000 feet (609.6 meters), unless
elevation requirements of over 2,000 feet (609.6 meters) were specified at the time the dryer order was
placed with the factory.  The adjustment or conversion of dryers in the field for elevations over 2,000 feet
(609.6 meters) are made by changing each burner orifice.  If this conversion is necessary, contact the
reseller who sold the dryer or contact the 

ADC

 factory.

Содержание AD-235D





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды