American DJ Fantasy Scan 250 Скачать руководство пользователя страница 18

American DJ

®

  -  www.americandj.com  - Fantasy Scan 250™ Instruction Manual Page 36

American DJ

®

  -  www.americandj.com  - Fantasy Scan 250™ Instruction Manual Page 35

  Fantasy Scan 250™  

 

 

 

      DMX Traits

Optimizing Lamp Alignment: 

This procedure centers the lamp in the 

reflector. Proper optimization will increase lamp life and ensure a bright 
crisp output. Improper optimization may add a yellow tint to the lamp 
output and reduce intensity.
1.  Be sure main power is disconnected and allow the unit to cool. If  
 

the you have just installed a new unit you can obviously skip this 

 

step.

2.   Make a preliminary adjustment: Turn the three lamp adjustment
 

thumb screws completely in (clockwise). Then back them each  

 

out (counter-clockwise) about three complete turns.

3.   Turn the unit on and allow it to reset.
4.   Using either a DMX controller or the control panel on the unit, 
 

strike the lamp and focus the light on a flat surface. Please see  

 

Spot on page 23.

5.   Center the hot-spot (the brightest part of the beam) using the 3 
 

adjustment screws. Turn one screw at a time to drag the hot-spot 

 

diagonally across the projected image. If you cannot detect a hot-

 

spot, adjust the lamp until the light is even.

6.   To reduce a hot-spot, pull the lamp in by turning all three screws 
 

clockwise 1/4-turn at a time until the light is evenly distributed.

7.   If the light is brighter around the edge than it is in the center, or if 
 

light output is low, the lamp is too far back in the reflector. “Push” 

 

the lamp out by turning the screws.

  Fantasy Scan 250™ 

                  Fuse & Lamp Replacement

Optimizing Screws

Optimizing Screws

Fuse Replacement:

 Locate and remove the unit’s power cord. Once 

the cord has been removed located the fuse holder located inside the 
power  socket.  Insert  a  flat-head  screw  driver  into  the  power  socket 
and gently pry out the fuse holder. Remove the bad fuse and replace 
with a new one. The fuse holder has a built-in socket for a spare fuse 
be sure not to confuse the spare fuse with active fuse.

  Channel 

   Value 

 

         Function

       

1               0 - 255                               PAN

       

2               0 - 255                               TILT

       

       3

              

 

        

                          COLOR WHEEL

                        0 - 127                    COLOR INDEXING
                    128 - 187           FORWARDS RAINBOW EFFECT
                                                        FAST           SLOW
                    188 - 193                        NO ROTATION
                    194 - 255         BACKWARDS RAINBOW EFFECT
                                                        SLOW          FAST
       4                                                  GOBO WHEEL
                        0 - 19                                CLOSE
                      20 - 39                     ROTATING GOBO 1
                      40 - 59                     ROTATING GOBO 2
                      60 - 79                     ROTATING GOBO 3
                      80 - 99                     ROTATING GOBO 4
                    100 - 120                   ROTATING GOBO 5
                    121 - 147             ROTATING GOBO 1 SHAKE
                    148 - 174             ROTATING GOBO 2 SHAKE
                    175 - 201             ROTATING GOBO 3 SHAKE
                    202 - 228             ROTATING GOBO 4 SHAKE
                    229 - 255             ROTATING GOBO 5 SHAKE
       5                                                GOBO ROTATION 
                         0 - 7                           NO ROTATION
                         8 - 255                          ROTATION

       6                                                PRISM ROTATION
                         0 - 7                            NO ROTATION                                      
                         8 - 127          FORWARDS PRISM ROTATION
                                                          FAST          SLOW
                     128 - 135                        NO ROTATION

Содержание Fantasy Scan 250





















Отзывы: