background image

AL-04
9806
aav#1534

For Models:

HRV 1500 IFD

HRV 1500 EFD

AAV1534

OPERATION AND

INSTALLATION MANUAL

NOTE: ALTHOUGH SOME MODELS
DIFFER IN OPERATION, THE BASIC
INSTALLATION STEPS ARE SIMILAR.

a

APPLICATION WARNING !!!

It is always important to assess how the operation
of any Heat Recovery Ventilator may interact with
vented combustion equipment (i.e., Gas Furnaces,
Oil Furnaces, Wood Stoves, etc.)

NEVER install an Heat Recovery Ventilator in a
situation where the normal operation (including
defrost function), lack of operation or partial failure
may result in the backdrafting or improper function-
ing of vented combustion equipment!!

TO BE COMPLETED BY CONTRACTOR AFTER INSTALLATION

___________________________________________________________________

Installing Contractor

___________________________________________________________________

Telephone / Contact

___________________________________________________________________

Serial Number

_______________________________     _________________________________

Installation Date                                               Model

Do Not Attempt Installing Unit Without First Reading Entire Manual

Note: Due to ongoing research and product development, specifications,
ratings and dimensions are subject to change with notice

For Models:

HRV 1500 SFD
HRV 1500 SFDE

Содержание 1500 SFDE

















Отзывы: