manualshive.com logo in svg

AMD Geode SC1200, Справочник данных

AMD Geode SC1200 - компактный и энергоэффективный встраиваемый процессор, идеальный для ноутбуков и компьютеров. Получите подробную информацию о его функциях и возможностях, загрузив Data Book бесплатно на нашем сайте. manualshive.com. Не упустите возможность получить нужное руководство.

Поделиться
Скачать
background image

144

AMD Geode™ SC1200/SC1201 Processor Data Book

Core Logic Module

32579B

6.2.2.1

Video Retrace Interrupt

Bit 7 of the “Serial Packet” can be used to generate an SMI
whenever a video retrace occurs within the GX1 module.
This function is normally not used for power management
but for SoftVGA routines. Setting F0 Index 83h[2] = 1
enables this function. A read only status register located at
I/O Offset 00h[5] can be read to see if the SMI
was caused by a video retrace event.

6.2.3

IDE Controller

The Core Logic module integrates a PCI bus mastering,
ATA-4 compatible IDE controller. This controller supports
UltraDMA, Multiword DMA and Programmed I/O (PIO)
modes. Two devices are supported on the IDE controller.
The data-transfer speed for each device can be indepen-
dently programmed. This allows high-speed IDE peripher-
als to coexist on the same channel as lower speed devices.

The Core Logic module supports two IDE channels, a pri-
mary channel and a secondary channel.

The IDE interface provides a variety of features to optimize
system performance, including 32-bit disk access, post
write buffers, bus master, Multiword DMA, look-ahead read
buffer, and prefetch mechanism for each channel respec-
tively.

The IDE interface timing is completely programmable. Tim-
ing control covers the command active and recover pulse
widths, and command block register accesses. The IDE
data-transfer speed for each device on each channel can
be independently programmed allowing high-speed IDE
peripherals to coexist on the same channel as older, com-
patible devices. 

The Core Logic module also provides a software accessi-
ble buffered reset signal to the IDE drive, F0 Index 44h[2].
The IDE_RST# signal can be driven low or high as needed
for device-power-off conditions. IDE_RST# is not driven
low by POR# (Power-On Reset). 

6.2.3.1

IDE Configuration Registers

Registers for configuring Channels 0 and 1 are located in
the PCI register space designated as Function 2 (F2 Index
40h-5Ch). Table 6-35 on page 256 provides the bit formats
for these registers. The IDE bus master configuration regis-
ters are accessed via F2 Index 20h which is Base Address
Register 4 in Function 2 (F2BAR4). See Table 6-36 on
page 260 for register/bit formats. 

The following subsections discuss Core Logic operational/
programming details concerning PIO, Bus Master, and
UltraDMA/33 modes.

6.2.3.2

PIO Mode 

The IDE data port transaction latency consists of address
latency, asserted latency and recovery latency. Address
latency occurs when a PCI master cycle targeting the IDE
data port is decoded, and the IDE_ADDR[2:0] and
IDE_CS# lines are not set up. Address latency provides the
setup time for the IDE_ADDR[2:0] and IDE_CS# lines prior
to IDE_IOR# and IDE_IOW#.

Asserted latency consists of the I/O command strobe
assertion length and recovery time. Recovery time is pro-
vided so that transactions may occur back-to-back on the
IDE interface without violating minimum cycle periods for
the IDE interface. 

If IDE_IORDY is asserted when the initial sample point is
reached, no wait states are added to the command strobe
assertion length. If IDE_IORDY is negated when the initial
sample point is reached, additional wait states are added.

Recovery latency occurs after the IDE data port transac-
tions have completed. It provides hold time on the
IDE_ADDR[2:0] and IDE_CS# lines with respect to the
read and write strobes (IDE_IOR# and IDE_IOW#).

The PIO portion of the IDE registers is enabled through:

•

Channel 0 Drive 0 Programmed I/O Register 
(F2 Index 40h)

•

Channel 0 Drive 1 Programmed I/O Register 
(F2 Index 48h)

•

Channel 1 Drive 0 Programmed I/O Register 
(F2 Index 50h)

•

Channel 1 Drive 1 Programmed I/O Register
(F2 Index 58h)

The IDE channels and devices can be individually pro-
grammed to select the proper address setup time, asserted
time, and recovery time. 

The bit formats for these registers are shown in Table 6-35
on page 256. Note that there are different bit formats for
each of the PIO programming registers depending on the
operating format selected: Format 0 or Format 1:

•

F2 Index 44h[31] (Channel 0 Drive 0 — DMA Control 
Register) sets the format of the PIO register. 

— If bit 31 = 0, Format 0 is used and it selects the 

slowest PIO mode (bits [19:16]) per channel for 
commands. 

— If bit 31 = 1, Format 1 is used and it allows indepen-

dent control of command and data.

Also listed in the bit formats are recommended values for
the different PIO modes. Note that these are only recom-
mended settings and are not 100% tested.

When using independent control of command and data
cycles the following algorithm should be used when two
IDE devices are sharing the same channel:

1)

The PIO data cycle timing for a particular device can
be the timing value for the maximum PIO mode which
that device reports it supports.

2)

The PIO command cycle timing for a particular device
must be the timing value for the lowest PIO mode for
both devices on the channel.

Содержание Geode SC1200




























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Geode SC1200

Campbell NL115 Instruction Manual preview
NL115
Бренд: Campbell Страницы: 42
MA lighting grandMA2 Series Quick Manual preview
grandMA2 Series
Бренд: MA lighting Страницы: 36
TE Connectivity InterReach Fusion ADCP-77-044 Manual preview
InterReach Fusion ADCP-77-044
Бренд: TE Connectivity Страницы: 236
Accusys ACS-76500 Owner'S Manual preview
ACS-76500
Бренд: Accusys Страницы: 34
Quectel Wi-Fi-M.2 EVB User Manual preview
Wi-Fi-M.2 EVB
Бренд: Quectel Страницы: 23
Bridgeworks a204 Hardware Manual preview
a204
Бренд: Bridgeworks Страницы: 18
e-con Systems ACC-CX3RDK-CU5640 Getting Started Manual preview
ACC-CX3RDK-CU5640
Бренд: e-con Systems Страницы: 9
NA DigiNet 416 User Manual preview
DigiNet 416
Бренд: NA Страницы: 22
Jaycar Electronics Duinotech Lilypad Plus XC3920 Quick Start preview
Duinotech Lilypad Plus XC3920
Бренд: Jaycar Electronics Страницы: 2
National Instruments NI 447 Series User Manual preview
NI 447 Series
Бренд: National Instruments Страницы: 80
Advantech SOM-C350 User Manual preview
SOM-C350
Бренд: Advantech Страницы: 108
Intel E5345 - Xeon 2.33 GHz 8M L2 Cache 1333MHz FSB LGA771 Active Quad-Core Processor Datasheet preview
E5345 - Xeon 2.33 GHz 8M L2 Cache 1333MHz FSB LGA771 Active Quad-Core Processor
Бренд: Intel Страницы: 112
Datum bc635VME Operation And Technical Manual preview
bc635VME
Бренд: Datum Страницы: 49
ADLINK Technology cPCIS-1100 Series User Manual preview
cPCIS-1100 Series
Бренд: ADLINK Technology Страницы: 48
National Instruments PCI-6601 User Manual preview
PCI-6601
Бренд: National Instruments Страницы: 52
Multiplex MULTIflight Stick Operating Instructions Manual preview
MULTIflight Stick
Бренд: Multiplex Страницы: 10
Areca ARC-12x4 Series Quick Installation Manual preview
ARC-12x4 Series
Бренд: Areca Страницы: 2
QSC Q-SYS QIO-GP8x8 Hardware User Manual preview
Q-SYS QIO-GP8x8
Бренд: QSC Страницы: 13

Бренды по названию

Популярные бренды

Загрузить еще бренды