manualshive.com logo in svg

AMD Elan SC520, Руководство пользователя

AMD Elan SC520 - мощный встроенный процессор, предназначенный для широкого спектра применений. Получите бесплатное пользовательское руководство на manualshive.com, чтобы узнать все возможности и функции этого устройства. Скачать руководство сейчас и ознакомьтесь с подробной информацией об AMD Elan SC520.

Поделиться
Скачать
background image

Reset Generation

6-8

Élan™SC520 Microcontroller User’s Manual

6.5.7

Determining Reset Sources

Status bits are available in the Reset Status (RESSTA) register (MMCR offset D74h) for 
software to determine the source of reset. These bits are set when the associated event is 
detected and cleared by writing a 1. They include:

■

ICE_HRST_DET—Hard CPU reset from AMDebug logic

■

ICE_SRST_DET—AMDebug system reset

■

WDT_RST_DET—Watchdog timer time-out system reset 

■

SD_RST_DET—Soft CPU reset resulting from a detection of the CPU shutdown cycle 
due to triple fault 

■

PRGRST_DET—System reset from PRGRESET pin that resets the ÉlanSC520 
microcontroller, allows SDRAM refresh, and maintains SDRAM configuration

■

PWRGOOD_DET—System reset from PWRGOOD pin

6.5.8

CPU A20 Gate Support

The ÉlanSC520 microcontroller does not support an a20 gate input pin. In a typical PC/AT 
system, this input was driven by the external System Control Processor (SCP) in response 
to a command request that is issued by the main CPU. In the ÉlanSC520 microcontroller, 
this a20 gate command sequence is detected by internal logic, and the appropriate action 
is taken.The ÉlanSC520 microcontroller provides an additional a20 gate source in the 
System Control Port A (SYSCTLA) register (Port 0092h). These two a20 gate sources are 
logically ORed such that both sources must be deasserted to cause the CPU’s a20 output 
to be gated Low.

The SCP a20 gate command is detected when the CPU issues the standard command 
write of D1h to the SCP Command Port (SCPCMD) register (Port 0064h), followed by a 
data write to the SCP Data Port (SCPDATA) register (Port 0060h). Bit 1 of the write to the 
SCP Data Port (SCPDATA) register drives the a20 control logic. A value of 1 allows the 
CPU’s a20 signal to propagate to the core logic, while a value of 0 allows the CPU’s a20 
signal to be driven Low, as long as no other a20 gate control sources are forcing the CPU’s 
a20 signal to propagate.

In addition to the SCP a20 gate command emulation, the A20G_CTL bit in the System 
Control Port A (SYSCTLA) register (Port 0092h) can also be used for alternate a20 signal 
control. Setting the A20G_CTL bit allows the CPU’s a20 signal to be propagated to the 
system logic. Clearing this bit (default state) allows the a20 signal to be driven Low as long 
as no other a20 gate control sources are forcing the a20 signal to propagate. 

6.5.9

Clocking Considerations

As a result of an ÉlanSC520 microcontroller system reset event, the internal PLLs are re-
started. The PLL start-up time from the deassertion of the system reset source is 10 ms.

6.5.10

Software Considerations

The CPU cache, SDRAM controller write buffer, and PCI transaction queues are discarded 
as a result of a system reset.

Содержание Elan SC520





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Elan SC520

ABB ControlMaster CM15 Commissioning Instructions preview
ControlMaster CM15
Бренд: ABB Страницы: 28
Nidec Leroy-Somer R180 Installation And Maintenance Manual preview
Leroy-Somer R180
Бренд: Nidec Страницы: 20
ABATEC A1 Installation And Operation Instruction Manual preview
A1
Бренд: ABATEC Страницы: 8
Parasound 7100 Owner'S Manual preview
7100
Бренд: Parasound Страницы: 72
Panasonic FP0 Series Specifications preview
FP0 Series
Бренд: Panasonic Страницы: 27
Panasonic CZ-64ESMC2 Instruction Manual preview
CZ-64ESMC2
Бренд: Panasonic Страницы: 78
Panasonic GM1 Series Reference Manual preview
GM1 Series
Бренд: Panasonic Страницы: 98
NAiS FP0 Series Hardware Manual preview
FP0 Series
Бренд: NAiS Страницы: 173
Panasonic SL-VGU1-EC Instruction Manual preview
SL-VGU1-EC
Бренд: Panasonic Страницы: 2
easydriver Pro Installation And Instruction Manual preview
Pro
Бренд: easydriver Страницы: 26
Calsense CS3000 Quick Start Manual preview
CS3000
Бренд: Calsense Страницы: 10
YOKOGAWA TC 10-L Engineering Manual preview
TC 10-L
Бренд: YOKOGAWA Страницы: 20
YOKOGAWA UTAdvanced UT32A Technical Information preview
UTAdvanced UT32A
Бренд: YOKOGAWA Страницы: 3
Linear Technology LT8570 Demo Manual preview
LT8570
Бренд: Linear Technology Страницы: 7
YASKAWA J1000 CIMR-JC series Installation Manual preview
J1000 CIMR-JC series
Бренд: YASKAWA Страницы: 25
YASKAWA CIMR-ZU Series Programming Manual preview
CIMR-ZU Series
Бренд: YASKAWA Страницы: 340
J+J J4C 20 Assembly Instructions Manual preview
J4C 20
Бренд: J+J Страницы: 6
NI RMC-8355 User Manual preview
RMC-8355
Бренд: NI Страницы: 135

Бренды по названию

Популярные бренды

Загрузить еще бренды