Ambirad VISION COMPACT Series Скачать руководство пользователя страница 19

19  User instructions for Ambi-Rad Vision Compact series of heaters

20  Important Information

Vision Compact is an overhead radiant heating system for industrial and commercial buildings.  The Vision Compact heater is suspended
horizontally overhead from the roof or inclined mounted at 30˚ to 45˚ from the horizontal and heats by radiation in the same way as the sun.

1. 

This appliance must only be installed by a competent person in accordance with the requirements of the Codes of Practice or the rules in 
force.

2.

Warning this appliance must be earthed.

3.

Never rest anything, especially ladders, against the heater.

To start the Vison Compact heater

1.

First ensure that the gas supply to the heater is turned on.

2.

Ensure that the settings of any time-switch and thermostat are such that the heating system will be required to operate.

3. 

Switch on electrical supply to heater.  Mains light, coloured red will illuminate and ignition sequence will commence.

4. 

After completion of an air purge period, ignition of the burner will occur and burner light, amber, will illuminate.

5.

If lock out occurs, switch off electrical supply, wait 15 seconds then switch on again.  If lock out occurs again switch off heater and call 
out a service engineer.

Note  U bend will glow, but this is acceptable.

To switch off Vision Compact heater

1.

Switch off electrical supply to the heater.  The burner will shut off and the fan will stop.

2.

If the heater is switched off for periods in excess of one week, it is highly recommended that both gas and electrical supplies are turned 
off.

Servicing

To ensure continued efficient and safe operation it is recommended that the heater is serviced regularly by a competent person e.g. every
year in normal working conditions but in exceptionally dust or polluted conditions more frequent servicing may be required.  The 
manufacturer, whose address is given below, offers a maintenance service.  Details available on request.

The data plate (supplied) should be attached on, or adjacent to a low level user control, as it contains the instructions for the safe operation
of the appliance including its lighting and shut-down procedures.

is the registered 

trademark of Ambi-Rad Limited. 

Due to continuous product 
innovation, Ambi-Rad reserves 
the right to change product 
specification without due notice. 

Ambi-Rad Limited  Fens Pool Avenue
Brierley Hill  West Midlands

DY

5 1

QA

United Kingdom

Telephone  01384 489700
Facsimile  01384 489707
UK sales email  sales

@

ambirad.co.uk

Website  www.ambirad.co.uk

Document reference number : GB/COB/112/0905

Содержание VISION COMPACT Series




















Отзывы: