background image

50D0112 

RCSTEBA Installation & Operating Manual     

Rel 1.0  April 2009

 

Page 11 of 10 

 Ambient Technologies 

A Division Of 

Monessen Hearth Systems

 

 

    desired ON/OFF delays. This is  
    done in minutes. 

 
 

WARNING:

 

Changes or modifications to this unit not expressly approved by the party responsible for 

compliance could void the user’s authority to operate the equipment.  
 
 
 

NOTE:

 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant 

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference 
in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not 
installed and used in accordance with instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does 
cause harmful interference to radio or television reception, which can be determined by turning the equipment off 
and on, the user is encouraged to try to correct the interference by one or more of the following measures: 
 

• Reorient or relocate the receiving antenna. 
• Increase the separation between the equipment and receiver. 
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 
• Consult the dealer or an experienced radio/TV technician for help. 
 
 
 
 
 
 
 
 

 

WARRANTY 

 

This warranty gives you specific legal rights and you may also have other rights that vary from state to state or 
province to province.  Answers to any questions regarding our limited warranty may be obtained by writing our 
corporate offices. 
 
Ambient Technologies warrants each new Ambient Technologies remote control against any defects that are due to 
faulty material or workmanship to the original owner, for a period of five years after the original date of purchase.  
This warranty and our liability does not apply to batteries, nor does it include damage to merchandise or the remote 
control resulting from accident, alteration, neglect, misuse, improper installation or any other failure to follow 
Ambient Technologies installation and operating instructions. 
 
After contacting Ambient Technologies Tech Service to receive a return authorization number, we agree

 

to repair or 

replace at our option any Ambient Technologies remote control under warranty. Provided it is returned postage 
prepaid to our warranty facility in a padded carton within the warranty period, with proof of the original date of 
purchase and a brief description of the malfunction.  This limited warranty does not include the cost of removal or 
re-installation. 

 
 
 
 

Ambient Technologies 

149 Cleveland Drive 

Paris KY 40361 

 

FOR TECHNICAL SUPPORT 

CALL 800-398-6195 

Содержание RCSTEBA












Отзывы: