Amazone ZA-V Скачать руководство пользователя страница 78

Страница: 78 / 136

Commissioning

ZA-V BAG0087.11 01.20

6.2

Adjusting the length of the PTO shaft to the tractor

WARNING
Danger from damaged and/or destroyed, flying parts if the PTO

shaft is upended or pulls apart while the machine coupled to the

tractor is being raised/lowered because the length of the PTO

shaft has not been adjusted properly.

Have the length of the PTO shaft in all operational positions checked

by a specialised workshop and, if necessary, adjusted before cou-

pling the PTO shaft to your tractor for the first time.
In this way, you prevent upending of the PTO shaft or insufficient

profile overlap.

This adjustment of the PTO shaft applies only for the current tractor

type. You may need to readjust the PTO shaft if you couple the ma-

chine to another tractor. Always observe the operating manual sup-

plied with the PTO shaft when adjusting the PTO shaft.

WARNING
Danger of being caught and drawn in if the PTO shaft is installed

incorrectly or if unauthorised design changes are made.

Only a specialist workshop may make design changes to the PTO

shaft. When doing so, read and follow the operating manual provided.
Adjusting the length of the PTO shaft is permitted with consideration

of the required minimum profile overlap.
Design changes to the PTO shaft that are not described in the PTO

shaft operating manual provided are not permitted.

WARNING
Danger of being crushed between the rear of the tractor and the

machine when raising and lowering the machine to determine

the shortest and longest operating position of the PTO shaft.

Only actuate the operator controls for the tractor's three-point linkage

•

from the intended workstation.

•

if you are outside of the danger area between the tractor and the

machine.

WARNING
Danger of crushing from unintentional:

•

Rolling of the tractor and the connected machine!

•

Lowering of the lifted machine!

Secure the tractor and machine from unintentional starting and unin-

tentional rolling and secure the machine unintentional lowering before

entering the danger zone between the tractor and lifted machine in

order to adjust the PTO shaft.

Содержание ZA-V









































































































































Результаты поиска

Содержание ZA-V

Отзывы:

Бренды по названию

Популярные бренды

Amazone ZA-V, Руководство по эксплуатации

Результаты поиска

Содержание ZA-V

Отзывы:

Бренды по названию

Популярные бренды