Amazone ZA-V Скачать руководство пользователя страница 55

Страница: 55 / 136

Structure and function

ZA-V BAG0087.11 01.20

Identification of the fertiliser

Representation of the ferti-

liser

Name of the fertiliser

Grain diameter

Bulk density

Calibration fac-

tor

The calibration factor is used as a default

value for fertiliser calibration.

If you cannot definitively assign the fertiliser to a kind listed in the

setting chart

•

the AMAZONE Fertiliser Service will assist you over the tele-

phone in assigning the fertilisers and setting recommendations.



+49 (0) 54 05 / 501 111

•

please consult the contact partner in your country

Boundary spreading:

•

ZA-V Hydro. Refer to the separate page in the setting chart.

(The fertiliser-specific pages of the setting chart show the set-

tings for boundary spreading with limiter.)

•

The fertiliser-specific setting charts "Shutter position for rate

setting" are only intended to set the rate on implements without

a control terminal

Содержание ZA-V









































































































































Результаты поиска

Содержание ZA-V

Отзывы:

Amazone ZA-V, Руководство по эксплуатации, Страница: 55 / 136

Результаты поиска

Содержание ZA-V

Отзывы: