Amazone Catros 2503 Special Скачать руководство пользователя страница 56

Страница: 56 / 70

Adjustments

Manual adjustment

1. Secure the tractor against unintentional

starting and unintentional rolling away.

2. Adjust the intensity using the crank and

secure the crank with the linch pin.

•

Turning the crank towards the right:

→

lower intensity

•

Turning the crank towards the left:

→

higher intensity

The display shows the set intensity.

(1) Crank

(2) Linch pin

(3) Read-off edge

(4) Scale

8.5

Adjusting the working depth of the tractor wheel mark eradicators

1. Secure the tractor against unintentional

starting and unintentional rolling away.

2. Pull out the rear pin (1).

3. Raise or lower the tractor wheel mark erad-

icators manually to the desired working
depth.

4. Make the adjustment with the pin in the

group of holes and secure using the linch
pin.

Catros BAG0160.4 02.19

Содержание Catros 2503 Special







































































Результаты поиска

Содержание Catros 2503 Special

Отзывы:

Бренды по названию

Популярные бренды

Amazone Catros 2503 Special, Руководство по эксплуатации

Результаты поиска

Содержание Catros 2503 Special

Отзывы:

Бренды по названию

Популярные бренды