![background image](http://html1.mh-extra.com/html/amano/07104/07104_operators-manual_2918214009.webp)
Machine Setup
To set-up your machine, follow this procedure:
1. Familiarize yourself with the machine and read all danger,
warning, and caution statements. Make sure all operators
of this machine have read this Operator's Manual. If they
cannot read this manual, have the manual explained fully
before allowing anyone to operate the sander.
2. Locate the electrical source. The receptacle should
be compatible with the plug. The receptacle must be
grounded and must be fused (see nameplate for electrical
requirements) to avoid an electrical hazard.
3. Clip the dust bag to the elbow. (See Figure 9) Cross the
strings on the dust bag and draw tight over the flare on the
elbow. Wrap the string around the elbow and secure.
4. Wind the electrical cord through the cable arm.
(See figure 10) Keep the power cord out of path of
equipment. Do not connect the electrical cord at this time.
9
Transporting the Machine by Carrying - Two People
1. Person #1
lifts the machine by the front handle.
2. Person #2 lifts the machine by the operating handle.
Figure 8
Figure 7
EN
Transporting the Machine - One Person
NOTE: This is accomplished by removing the motor from the chassis
and transporting the motor and chassis separately.
To transport the machine, follow this procedure:
1. Make sure the power cable is disconnected from the electrical outlet.
2. Release the tension on the drive belts using the quick release lever.
(See Figure 6A
)
3. Open the belt guard by pulling on the handle immediately above the
left truck wheel. (See Figure 6B)
4. Remove the drive belts from the machine
5. Disconnect the motor pigtail from the handle pigtail if so equipped.
(See Figure 7)
6. Unscrew the motor mounting knobs to loosen the motor.
(See Figure 8)
7. Straddle the motor and grasp the motor lift handle. Using your legs,
lift the motor off the chassis and take it to the work site.
8. Lift the chassis by grasping the front and rear handles. Lift the frame
and bring the belt guard against your chest. Take the chassis to the
work site.
To assemble the machine after transporting, follow this procedure:
1. Open the belt guard door. Place the motor assembly on the chassis
and screw the motor mounting knobs sufficiently to engage and
secure the motor.
2. Install the drive belts. Tighten the belts using the belt tension quick
release lever.
3. Check the tension on the belts and close the belt guard door.
CAUTION: Premature bearing failure can occur if the fan belt
is set too tight. The fan belt should deflect ½” at
the center of the span with 5 lbs. of pressure.
NOTE:
It is necessary to adjust the fan belt independently
during this procedure or during replacement. The
idler pulley is factory adjusted.
Содержание 07104
