background image

CONDENSING UNIT

*VXC20

 Air Conditioning Installation & service reference

IOG-4014A

07/2020

Only personnel that have been trained to install, adjust, 

service or repair(hereinafter, “service”) the equipment 

specified in this manual should service the equipment.  

The manufacturer will not be responsible for any injury 

or property damage arising from improper service or 

service procedures.  If you service this unit, you assume 

responsibility for any injury or property damage which may 

result.  In addition, in jurisdictions that require one or more 

licenses to service the equipment specified in this manual, 

only licensed personnel should service the equipment.  

 

Improper installation, adjustment, servicing or repair of 

the equipment specified in this manual, or attempting to 

install, adjust, service or repair the equipment specified in 

this manual without proper training may result in product 

damage, property damage, personal injury or death.

WARNING

19001 Kermier Rd. Waller, Tx 77484

www.goodmanmfg.com•www.amana-hac.com

© 2020 Goodman Manufacturing Company, L.P. 

 is a registered trademark of Maytag Corporation or its related companies and is used under license. All rights 

reserved.

IMPORTANT SAFETY INSTRUCTIONS

The following symbols and labels are used throughout 

this manual to indicate immediate or potential safety 

hazards.  It is the owner’s and installer’s responsibility to 

read and comply with all safety information and instructions 

accompanying these symbols.  Failure to heed safety 

information increases the risk of personal injury, property 

damage, and/or product damage.

WARNING

High Voltage!

Disconnect all power before servicing or 

installing this unit.  Multiple power sources may 

be present.  Failure to do so may cause property 

damage, personal injury or death.

CAUTION

Do not wash the condensing unit with excessive water. An 

electric shock or fire could result. 

WARNING

PROP 65 WARNING 

FOR CALIFORNIA CONSUMERS

Cancer and Reproductive Harm -

www.P65Warnings.ca.gov

0140M00517-A

“Proper sizing and installation of equipment is critical to achieve optimal performance.  Split system 

air conditioners and heat pumps must be matched with appropriate coil components to meet ENERGY 

STAR criteria.  Ask your contractor for details or visit www.energystar.gov. 

 

IMPORTANT – This product has been designed and manufactured to meet ENERGY STAR criteria for 

energy efficiency when matched with appropriate coil components. However, 

 

proper refrigerant charge and proper air flow are critical to achieve rated capacity and 

 

efficiency. Installation of this product should follow the manufacturer’s refrigerant charging and air 

flow instructions.

 Failure to confirm proper charge and airflow may reduce 

 

energy efficiency and shorten equipment life.”

Содержание VXC20 Series





























































Отзывы: