Amana HDC-60 Скачать руководство пользователя страница 9

7

 

Models

HDC12*

HDC18* 

CRC18T2OG

HDC21*

CRC21T2RL

Power Source

Voltage AC

120V

208 - 240V

208 - 240V

Amperage

20 A

20 A

20 A

Frequency

60 Hz

60 Hz

60 Hz

Single Phase, 3 wire grounded

X

X

X

%4334

NEMA 5-20

NEMA 6-20

NEMA 6-20

Power Output

Nominal microwave energy 
(IEC705)

1200 W

1800 W

2100 W

Minimum temperature rise

12°F / 6.5°C

18°F / 10°C

21°F / 11.5°C

Operating Frequency

2450 MHz

2450 MHz

2450 MHz

Power Consumption

Cook Condition Microwave

2000 W, 16.8 A

3000 W@ 208v, 14.4 A
3000W @ 240v, 12.5 A

3200 W@ 208v, 15.4 A
3200 W@ 240v, 13.4 A

Dimensions

Cabinet

Width

16¾” (425)

  16¾” (425)

16¾” (425)

Height

13½” (343)

  13½” (343)

13½” (343)

Depth

22” (559)

  22” (559)

22” (559)

Cavity Dimensions 

Width

13” (330)

  13” (330)

13” (330)

Height

6 ¾” (171)

  6 ¾” (171)

6 ¾” (171)

Depth

12” (305)

  12” (305)

12” (305)

Weight

Crated

73 lbs.  (33 kg.)

73 lbs.  (33 kg.)

73 lbs.  (33 kg.)

Uncrated

67 lbs. (30 kg.)

67 lbs. (30 kg.)

67 lbs. (30 kg.)

Unpacking Oven 

‚  ='346

dents inside oven cavity. 

‚ F  _3 4'46

immediately. Do not attempt to use oven if damaged.

‚ F= '=
‚ '=6 ? ^,

few hours before connecting power. 

Radio Interference

Microwave operation may cause interference to radio, 
television, or similar a oven. Reduce or eliminate 
interference by doing the following:
‚ 34''=3

instructions in “Care and Cleaning” section.

Installation

‚ %^ =^ ' 

from oven.

‚ ƒ  ^ =^

to obtain stronger signal reception.

Содержание HDC-60













































Отзывы: