Amana HDC-60 Скачать руководство пользователя страница 6

4

PRECAUTIONS TO AVOID POSSIBLE 

EXPOSURE TO EXCESSIVE MICROWAVE 

ENERGY

A. 

DO NOT

 attempt to operate this oven with the door open since open door operation can result in harmful 

exposure to microwave energy. It is important not to defeat or tamper with the safety interlocks.

B. 

DO NOT

 place any object between the oven front face and the door too allow soil or cleaner residue to 

accumulate on sealing surfaces.

C. 

DO NOT

 operate the oven if it is damaged. It is particularly important that the oven door close properly and 

that there is no damage to the:

1. door 

(bent)

2.  hinges and latches (broken or loosened)
3.  door seals and sealing surfaces.

 /6=64 >4 ? @4=

SAVE THESE INSTRUCTIONS

1.  READ all instructions before using equipment.

 F*&&"HJ!!J7 6

“PRECAUTIONS TO AVOID POSSIBLE 
EXPOSURE TO EXCESSIVE MICROWAVE 
ENERGY” on this page.

 3.  This equipment MUST BE GROUNDED. Connect 

only to properly GROUNDED outlet. See “ 
GROUNDING / EARTHING INSTRUCTIONS” on 
page 5.

 4.  Install or locate this equipment ONLY in 

accordance with the installation instructions in 
this manual.

 5.  Some products such as whole eggs and sealed  

containers—for example, closed glass jars—are 
able to explode and SHOULD NOT be HEATED 
in this oven.

6.  Use this equipment ONLY for its intended use as 

described in this manual. Do not use corrosive 
chemicals or vapors in this equipment. This type 
'=3 6 ^_^
or dry food. It is not designed for industrial or 
laboratory use.

7.   As with any equipment, CLOSE SUPERVISION 

is necessary when used by CHILDREN.

8.  See door cleaning instructions on page A-4 of 

this owners manual.

9.  DO NOT heat baby bottles in oven.

10.  Baby food jars shall be open when heated and 

contents stirred or shaken before consumption, in 
order to avoid burns.

11  DO NOT operate this equipment if it has a 

damaged cord or plug, if it is not working properly, 
or if it has been damaged or dropped.

12.  This equipment, including power cord, must be 

=J"!{@4=
Special tools are required to service equipment. 
Contact nearest authorized service facility for 
examination, repair, or adjustment.

13.  DO NOT cover or block louvers or other openings 

on equipment.

14.  DO NOT store this equipment outdoors. DO NOT 

use this product near water – for example, near a 
kitchen sink, in a wet basement, a swimming pool, 
or a similar location.

15.  DO NOT immerse cord or plug in water.

16.  Keep cord AWAY from HEATED surfaces.

17.  DO NOT let cord hang over edge of table or 

counter.

18.  For commercial use only.

When using electrical equipment, basic safety precautions should be followed to reduce the risk of burns, 
 6_^^>4 43 6',3

IMPORTANT SAFETY INSTRUCTIONS

   Recognize this symbol as a SAFETY message

!

WARNING

Содержание HDC-60













































Отзывы: