manualshive.com logo in svg

Amana HDC-60, Руководство по обучению обслуживанию, Страница: 32 / 44

Поделиться
Скачать
Amana HDC-60 Скачать руководство пользователя страница 32

30

 

Error Code Table 

Error Code 

Corrective Action 

F1 Replace 

HV/LV 

Board 

F2 Replace 

HV/LV 

Board 

F3 Replace 

HV/LV 

Board 

F4 Replace 

HV/LV 

Board 

F5 Replace 

Touch 

Panel 

Usage Test 

The Usage Test is used to access Magnetron Hours, Magnetron Cycles and Door Cycles. Use the following 
procedure to access the data: 

1. Open 

door. 

2.  Press and hold pad 

3

 for five (5) seconds. 

NOTE:

  After five (5) seconds, SErv illuminates in the display. 

3. Press 

pad 

1

 for Magnetron Hours. 

4. Press 

pad 

2

 for Magnetron Cycles. 

5. Press 

pad 

3

 for Door Cycles. 

 

Conditions 

Initial Power Up Condition:

  Apply power to oven with door closed. 

Idle Condition:

 

Oven plugged in, display blank (no other components operating). 

Standby Condition:

 

Open oven door, light and motors operate. 

Cook Condition:

 

Food load in oven, cook cycle initiated. 

F6 Replace 

HV/LV 

Board 

Component Testing Procedures

Содержание HDC-60













































Отзывы:

Нет отзывов