Amana DD01E Скачать руководство пользователя страница 1

PTAC

WIRELESS KITS (DT01*, DS01E, DD01E, DD01F)

I

NSTALLATION

  I

NSTRUCTIONS

1/2013
IO-729C

The following installation instructions are for a typical installation.

Please contact your PTAC salesperson

for additional assistance and explanation prior to ordering materials or cutting openings.

DS01E

DD01E

DT01A

DT01G

ATTENTION INSTALLING PERSONNEL

As a professional installer you have an obligation to know the product better than the customer.

This includes all safety precautions and related items.

Prior to actual installation, thoroughly familiarize yourself with this Instruction Manual.

Pay special attention to all safety warnings. Often during installation or repair

it is possible to place yourself in a position which is more hazardous than when the unit is in operation.

Remember, it is your responsibility to install the product safely and to know it well enough

to be able to instruct a customer in its safe use.

Safety is a matter of common sense...a matter of thinking before acting.

Most dealers have a list of specific good safety practices...follow them.

The precautions listed in this Installation Manual are intended as supplemental to existing practices.

However, if there is a direct conflict between existing practices and the content of this manual,

the precautions listed here take precedence.

Heating & Air Co nditioning

®

A

AIR CONDITIONING SENSOR

DD01F

AIR CONDITIONING SENSOR

PTAC Direct Sales, Inc.

 

185 S. Kimball Ave.

 

Suite 130

Southlake, TX 76092

 

877.454.7822 (T)

 

877.647.6408 (F)

Содержание DD01E

















Отзывы: