Amana CVC96 BB Series Скачать руководство пользователя страница 32

Страница: 32 / 52

software updates have been installed. Review

notes for optional software updates and install if

necessary.

NOTE: If an E11 code exists for the inverter system

immediately after line voltage is applied (code shown in the

CoolCloud HVAC phone application or displayed on the

inverter control), the System Verification Test needs to be

completed before any other operation. See the following

procedure.

1. Allow the system to remain Idle for 5 minutes.

Turn the system verification test on either by using

the phone application, or by entering the

SUt

through the furnace push buttons.

3. Wait for the test to complete.

Charging

1. Inverter units using the

CoolCloud

HVAC phone

application or control board push button:

a. Inverter units are charged by setting

the CR9 menu (Charge Mode) to ON through

the furnace control board push buttons

or through the

CoolCloud

HVAC phone

application.

b. The System will remain in charge mode (high

speed) for 60 minutes before timing out.

The installer must manually shut off charge

mode once complete.

2. Two-stage outdoor units using the

CoolCloud

HVAC

application:

Using the cooling icon after entering the outdoor

unit menus, energize the outdoor unit at 100%

capacity.

b. Charge the outdoor unit as required using the

charging information provided with the outdoor

equipment.

Gas Furnace Testing

1. Two-stage Operation using the

CoolCloud

HVAC

application:

a. Select the gas heat icon after entering the

furnace menus.

b. Select any value less than 50% for low stage

operation and any value greater than 50% for

high stage operation.

4. Confirm thermostat heating and cooling calls function

proprly with equipment.

Quick Start Guiide For Non-Communicating

Outdoor Units

When setting up a ComfortBridge™ furnace for use

with a Non-Communicating outdoor unit you must

set airflow in the “ton” menu on the PCB or in the

CoolCloud HVAC APP. Failure to do so will result in

the furnace PCB displaying “

IdL

” and the blower will

not operate with a call for cooling. The Board does not

need to be replaced, you MUST set the airflow first.

instructed by the applicable wiring diagrams shown in

this section.

2. Connect the 1 & 2 wires between the indoor and

outdoor unit for communicating operation.

Note: verify two stage outdoor units include a 24 VAC

transformer (for outdoor control board power) Two

stage outdoor units may not behave properly without

this 24 VAC transformer.

R
C

Optional

Optional if

feature

supported by

thermostat

INDOOR

BOARD TERMINAL

CONNECTIONS

OUTDOOR

BOARD TERMINAL

CONNECTIONS

OUTDOOR

TRANSFORMER

R
C

Communicating Two Stage Air Conditioner or Heat

Pump

Figure 49

R
C

Optional

INDOOR

BOARD TERMINAL

CONNECTIONS

OUTDOOR

BOARD TERMINAL

CONNECTIONS

R
C

24 VAC

Thermostat

Communicating Inverter Air Conditioner or Heat

Pump

Figure 50

Download the

CoolCloud

HVAC phone application for

charging and to configure/test system operations.

NOTE: When new versions of Bluetooth

Communication Software and Furnace Control

Software are available, the phone application

notifies the user. Software updates are classified

as either optional or mandatory and installed by

using the phone application. Ensure all mandatory

Содержание CVC96 BB Series





















































Результаты поиска

Содержание CVC96 BB Series

Отзывы:

Похожие инструкции для CVC96 BB Series

Бренды по названию

Популярные бренды

Amana CVC96 BB Series, Руководство по установке

Результаты поиска

Содержание CVC96 BB Series

Отзывы:

Похожие инструкции для CVC96 BB Series

Бренды по названию

Популярные бренды