background image

25

Drip Leg

Plug in Main Gas Line Hole

Alternate

Union

Location

Manual Shut Off Valve

          (upstream from

            ground joint pipe union)

Gas

Valve

Burners

Drain Trap

Manifold

Plug in Alternate Gas Line Hole

Grommet in

Standard Gas Line Hole

Figure 34 

Manual Shut Off Valve

          (upstream from

            ground joint

            pipe union)

Figure 35 

Gas Piping Checks 

CAUTION

To avoid the possibility of explosion or fire, 

never use a match or open flame to test for 

leaks. 

Before placing unit in operation, leak test the unit and gas 

connections.

Check for leaks using an approved chloride-free soap and 

water solution, an electronic combustible gas detector, or 

other approved testing methods.

aluminum-alloy tubing and connectors are coated to 

protect against external corrosion when in contact 

with masonry, plaster, or insulation, or subjected to 

repeated wetting by liquids such as water (except rain 

water), detergents, or sewage.

The gas piping may enter the left or right side of the 

furnace cabinet. The installer must supply rigid pipe long 

enough to reach the outside of the cabinet to seal the 

grommet cabinet penetration.  A semi-rigid connector to the 

gas piping can be used outside the cabinet per local codes. 

1/2” NPT pipe and fittings are required.  For models with an 

“L” shaped manifold, a 4 1/2” long nipple is required.  For 

models with a hook shaped manifold, a 2” long nipple is 

required.

A semi-rigid connector to the gas piping can be used 

outside the cabinet per local codes. From the elbow, the 

length of pipe and the fittings required will vary by the side 

chosen, location of union and cabinet width. The union may 

be placed inside or outside of the cabinet.

Alternate

Gas Line

Location

Gas Valve

Burners

Manual Shut Off Valve

(upstream from

ground joint

         pipe union)

Drip Leg

Grommet

in Standard

Gas Line

Hole

*Ground

Joint

Pipe

Union

*Ground

Joint

Pipe

Union

*NOTE: Union may be inside furnace cabinet where allowed by local codes.

Manifold

Figure 32 

Alternate

Gas Line

Location

Plug in

Alternate

Gas Line

Hole

Gas Valve

Burners

Manual Shut Off Valve

(upstream from ground joint pipe union)

Drip Leg

Grommet

in Standard

Gas Line

Hole

*Ground

Joint

Pipe Union

*Ground

Joint

Pipe Union

*NOTE: Union may be inside furnace cabinet where allowed by local codes.

Figure 33 

Содержание CVC96 BB Series





















































Отзывы: