ALUZ A1-ZIBI-PVT-RGBW Скачать руководство пользователя страница 8

Страница: 8 / 11

Installation Instructions

1170 N Red Gum St, Anaheim, CA 92806

[email protected]

aluz.lighting

866.ALUZ.LTG | 714.535.7900

A1 Series

Surface

ZIBI

Pivot RGBW

(A1-ZIBI-PVT-RGBW)

Page 8 of 11

4 / 29 / 2022 / Rev 2

Louver (A1-ZIBI-PVT-LVR)

Set Screw

12”

Min. from Wall

Set Screw

Shrink Tube

Apply Heat

2”

Determine number of louvers needed. Louvers are available in 1’ increments.

Specify total length of reflectors needed.

If applicable, connect disconnects between luminaires. Slide shrink tube over

connectors and apply heat. The shrink tube will shrink down, sealing the

connectors. Apply silicone around sealed connectors for a stronger seal.

Mount luminaires at least 12” away from the wall.

Position louvers on luminaires.

Install 3 set screws on each louver to secure in place.

Do not over-tighten set screws

Содержание A1-ZIBI-PVT-RGBW












Результаты поиска

Содержание A1-ZIBI-PVT-RGBW

Отзывы:

Бренды по названию

Популярные бренды

ALUZ A1-ZIBI-PVT-RGBW, Руководство пользователя

Результаты поиска

Содержание A1-ZIBI-PVT-RGBW

Отзывы:

Бренды по названию

Популярные бренды