manualshive.com logo in svg

ALUZ A1-ZIBI-PVT-RGBW, Руководство пользователя

Поделиться
Скачать
ALUZ A1-ZIBI-PVT-RGBW Скачать руководство пользователя страница 10

Installation Instructions

1170 N Red Gum St, Anaheim, CA 92806

©  ALUZ All Rights Reserved. ALUZ reserves the right to make changes or withdraw specifi cations without prior notice.

[email protected]

aluz.lighting

866.ALUZ.LTG | 714.535.7900

A1 Series 

|

 

Surface

ZIBI

 

Pivot RGBW

(A1-ZIBI-PVT-RGBW)

Page 10 of 11

4 / 29 / 2022 / Rev 2

Operating the Pivot Function

Turn knob to tighten

Upper Extrusion

Lower Extrusion

Pivot Lock Bar

Pivot Lock Knob

Turn knob to loosen

1

Slightly unscrew Pivot Lock Knobs on both ends of luminaire until Pivot Lock Bar 

and Upper Extrusion are able to move freely. Do not remove Pivot Lock Knob.

DIAGRAM OF ASSEMBLY

2

Adjust angle as desired.

Tip:

 Use an angle fi nder or sliding bevel to ensure accuracy of angles.

3

Turn the Pivot Lock Knob until tight against Pivot Lock Bar. Repeat on other end 

of luminaire. Do not overtighten Pivot Lock Knob.

Содержание A1-ZIBI-PVT-RGBW












Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды