background image

47-0038-00 • RevB • 2018-04-02

 Tech Support Line • (888) 88-ALULA • (888) 882-5852

alula.net

WARRANTY

Alula will replace non-portable products that are defective in their 

first five (5) years and portable products that are defective in their 

first two (2) years.  

FCC NOTICE

This device complies with Part 15 of the FCC rules. Operation is 

subject to the following two conditions:
(1) This device may not cause harmful interference.

(2) This device must accept any interference that may be received, 

including interference that may cause undesired operation.

Changes or modifications not expressly approved by Alula could 

void the user’s authority to operate this equipment.
RF Exposure:
To satisfy FCC RF Exposure requirements for mobile and base 

station transmission devices, a separation distance of 20 cm or 

more should be maintained between the antenna of this device 

and persons during operation. To ensure compliance, operation at 

closer than this distance is not recommended.

TRADEMARKS

ALULA IS A TRADEMARK OWNED BY ALULA HOLDINGS, LLC.

“GE”, “INTERLOGIX”, “HONEYWELL”, “DSC”, “2GIG”, “QOLSYS” 

AND, “NAPCO” ARE TRADEMARKS OWNED BY GENERAL ELEC-

TRIC COMPANY, UNITED TECHNOLOGIES ELECTRONIC CON-

TROLS INC.,  HONEYWELL INTERNATIONAL INC., TYCO SAFETY 

PRODUCTS CANADA LTD, NORTEK SECURITY & CONTROL LLC, 

TYCO SAFETY PRODUCTS CANADA LTD, NAPCO SECURITY TECH-

NOLOGIES, INC., AND  RESPECTIVELY.  

ALULA PRODUCTS WILL FUNCTION WITH ONE OF EITHER 

INTERLOGIX (FORMERLY GE), HONEYWELL, DSC, 2GIG , QOLSYS 

OR NAPCO SYSTEMS.  HOWEVER, NO ALULA PRODUCT IS PRO-

DUCED BY, ENDORSED BY, NOR IS OFFICIALLY ASSOCIATED WITH 

INTERLOGIX (FORMERLY GE), HONEYWELL, DSC, 2GIG, QOLSYS 

OR NAPCO. ALULA RECOMMENDS VERIFYING PROPER ENROLL-

MENT AND OPERATION, PER CONTROL PANEL INSTALLATION 

INSTRUCTIONS, AT INSTALLATION.

Physical 

Housing Dimensions
Weight
Mounting Fastener
Reported Indications
Current Draw

8.5 x 5.0 x 1.3 inches
10.0 ounces
#4 or #6 (not provided) 
Cover Tamper, Wall Tamper
200mA (Nominal)

Environmental

Operating Temperature 
Maximum Humidity

32°F to 120°F
85% non-condensing relative humidity

Panel Compatibility

Honeywell
DSC

Caddx
Interlogix
Napco
Paradox
Texecom

Vista 15P, Vista 20P
PC580 (Power 432), PC1555 (Power 632) ,
PC1555MX (Power 632), PC5010 (Power 832), 
C5020 (Power 864) , PC5015 (Power 832), PC1616, PC1832, 
PC1864
All NX series panels
Concord 4
GEM P800, GEM P801, GEM P816 GEM P1632
MG5050
None yet

Models

RE929X-00-01
RE929X-01-01

Flex LTE IGM
Flex LTE IGM with Zwave

Certification

RE929X

FCC, Verizon

 

Specifications

Specifications subject to change without notice

Содержание RE929X Series

















Отзывы: