HubWayLD Active Unit
- 3 -
Installation Instructions:
1. Attach mounting brackets to HubWayLD8CD/LD16CD unit for rack or wall mount installation (Figs. 6a-6b, 7a, pg. 8).
Affix rubber pads to HubWayLD8CD/LD16CD for shelf installation (Fig. 8, pg. 8).
2. Secure the unit in a rack, mount unit to a wall or place unit on a shelf as desired (unit should be spaced at least 3”
from any video monitors) (Figs. 6c, 7b, pg. 8).
3. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 5, pg. 7).
4. Plug the grounded AC line cord (included) into the IEC 320 connector of the HubWayLD8CD/LD16CD
unit
(Fig. 1j, pg. 4). Insert the plug end of the line cord into a grounded 115VAC receptacle.
5. Set voltage output selector switch for each camera channel for 24VAC or 28VAC (Fig. 1d, pg. 4).
6. Connect the BNC video outputs for HubWayLD8CD/LD16CD Channels 1 - 8 (Channels 1-16) to the
corresponding video inputs on the head end equipment (DVR) (Fig. 1f, pg. 4).
7. Connect the RS422/RS485 output of the head end equipment (DVR) to the one (1) or both data input terminal
blocks of the HubWayLD8CD/LD16CD unit (polarity must be observed) (Fig. 1e, pg. 4).
Note: The Data input terminals of the HubWayLD8CD/LD16CD must be wired in parallel for proper
operation. When using fixed cameras disregard this step.
8. Connect Video Balun/Combiner at camera 1 to the HubWayLD8CD/LD16CD unit utilizing CAT-5 or higher structured
cable. Plug the RJ45 connector at one end of the structured cable into the RJ45 jack marked [Channel 1] of the
HubWayLD8CD/LD16CD
(Fig. 1a, pg. 4). Plug the RJ45 connector at the opposite end of the structured cable into
the RJ45 jack of the Video Balun/Combiner located at camera 1.
• For 24VAC cameras use Altronix model HubWayAv/HubWayAv2 Video Balun/Combiner (Figs. 2a, 2b, 2e, pg. 5).
• For 12VDC cameras use Altronix model HubWayDv Video Balun/Combiner (Figs. 2c, 2d, pg. 5).
• For non-isolated 12VDC cameras use Altronix model HubWayDvi Video Balun/Combiner (Figs. 2c, 2d, pg. 5).
Repeat steps 6-8 for each additional camera (Channels 2-8 or Channels 2-16).
Note: When a particular camera exceeds the maximum distance for power transmi ssion, a local external power source
is required. Optionally, an Altronix HubSat4D Passive UTP Transceiver Hub with Integral Camera Power may be
utilized
(Fig. 4a, pg. 6). The combined total cable distance for video transmission must not exceed 3000 ft. between
the HubWayLD8CD/LD16CD and each camera routed through the HubSat4D.
9. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 5, pg. 7) and measure the
output voltage at the power output terminals of each Video Balun/Combiner (Figs. 2b, 2d, pg. 5) before powering
each camera to ensure proper operation and avoid possible damage.
• HubWayAv/HubWayAv2 - Terminals marked [AC POWER] (Figs. 2a, 2b, 2e, pg. 5).
• HubWayDv/HubWayDvi - Terminals marked [– 12VDC +] (Figs. 2c, 2d, pg. 5).
10. Set illuminated master power disconnect circuit breaker to the (OFF) position to make the final connections (Fig. 5, pg. 7).
11. Connect the power outputs of the HubWayAv, HubWayAv2, HubWayDv or HubWayDvi Video Balun/Combiners
to the power inputs of the cameras (Figs. 2a-2e, pg. 5). Polarity must be observed.
12. Connect the terminals marked [+ DATA -- ] of the HubWayAv, HubWayAv2, HubWayDv or HubWayDvi Video
Balun/Combiners to the data terminals of the cameras for PTZ control (Figs. 2a-2e, pg. 5). Polarity must be observed.
When installing fixed cameras disregard this step.
13. Connect the BNC connectors of the HubWayAv, HubWayAv2, HubWayDv or HubWayDvi Video Balun/Combiners
to the BNC video outputs of the cameras (Figs. 2a-2e, pg. 5).
14. Upon completion of wiring set illuminated master power disconnect circuit breaker to the RESET (ON) position
(Fig. 5, pg. 7).
15. The power LEDs (Red) located on the front of the HubWayLD8CD/LD16CD will illuminate when AC power
is present (Fig. 1c, pg. 4).
Note: If any of these LEDs are not illuminated either a voltage output selector switch is in the OFF position or the
PTC is tripped for that channel.
To reset the PTC:
1. Set the voltage output selector switch for that corresponding channel to the OFF position. Switch must remain
in the OFF position for approximately 2 minutes in order for the PTC to reset.
2. Eliminate the trouble condition (short circuit or overload).
3. Set the voltage output selector switch for 24VAC or 28VAC (Fig. 1d, pg. 4).
16. AC LEDs (Green) of the HubWayAv or DC LEDs (Red) of the HubWayDv/HubWayDvi Video Balun/Combiners
will illuminate indicating power is present at the cameras (Fig. 2b, 2d, pg. 5).
17. The video signal indicator LEDs (Red) located on the rear of the HubWayLD8CD/LD16CD will illuminate when
video signal is present (Fig. 1i, pg. 4). If any of these LEDs are not illuminated, no video signal is present for
that corresponding channel.
18. Optimize the picture quality for all camera channels by adjusting the corresponding potentiometers
marked [Picture] (Fig. 1g, pg. 4).
19. Set gain for all camera channels by adjusting the corresponding potentiometers marked [Gain] (Fig. 1h, pg. 4).
