Altronix AL1012M220, Руководство по установке

Страница: 3 / 16

M220 Series - 3 -
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/NFPA 72/ANSI, and with
all local codes and authorities having jurisdiction. Product is intended for indoor use only.
1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes
in the enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place
the enclosure’s upper keyholes over the two upper screws; level and secure. Mark the position of the lower
two holes. Remove the enclosure. Drill the lower holes and install three fasteners. Place the enclosure’s
upper keyholes over the two upper screws. Install the two lower screws and make sure to tighten all
screws (Enclosure Dimensions, pg. 15, 16). Secure enclosure to earth ground.
It is recommended to first review the following tables for screw terminals, switch selection and
LED status indications. This will greatly facilitate installation hook-up.
Carefully review:
Output Voltage & Stand-by Specifications (pg. 5) Terminal Identification Table (pg. 10)
LED Diagnostics (pg. 4) Typical Application Diagrams (pgs. 11 & 12)
2. Set output voltage:
AL300M220, AL400M220 (Fig. 1c, pg. 5) and AL600M220 (Fig. 2c, pg. 6): set desired DC output voltage
by setting switch SW1 to the appropriate position on the power supply board.
AL1012M220 is 12VDC only. AL1024M220 is 24VDC only.
(Output Voltage and Stand-by Specification Charts, pg. 5).
3. Secure green lead (earth ground) to ground lug. Connect AC power (115VAC, 60Hz) to the terminals
marked [L, G, N] on power supply board (Figs. 1 - 4, pgs. 6 - 9).
Use 18 AWG or larger for all power connections (Battery, DC output, AC input).
Use 22 AWG to 18 AWG for power-limited circuits (AC Fail/Low Battery reporting).
4. Measure output voltage before connecting devices. This helps avoiding potential damage.
Keep power-limited wiring separate from non power-limited wiring (220VAC, 50/60Hz Input,
Battery Wires). Minimum 0.25” spacing must be provided.
CAUTION: Do not touch exposed metal parts. Shut branch circuit power before installing or
servicing equipment. There are no user serviceable parts inside.
Refer installation and servicing to qualified service personnel.
5. Connect Fail-Secure type locking hardware (e.g. door strikes and electronic dead bolts) positive leads to
terminals marked [1] through [5] [POS. (+) DC OUTPUT (ALARM)] on MOM5 board and the negative
leads to terminals marked [NEG 1] through [NEG 5] on MOM5 board (Figs. 1 - 4, pgs. 6 - 9).
6. Connect Fail-Safe type locking hardware (e.g. mag locks, door strikes and door holders) positive leads to
terminals marked [6] through [10] [POS. (+) DC OUTPUT (STAND-BY)] on MOM5 board and negative
leads to terminals marked [NEG 1] through [NEG 5] on MOM5 board (Figs. 1 - 4, pgs. 6 - 9).
7. To trigger the unit from a FACP connect signaling circuit of FACP to terminals marked [– INPUT +] on
MOM5 board (Figs. 1 - 4, pgs. 6 - 9). Polarity is shown in alarm condition.
For latching fire alarm interface see Fig. 7, pg. 11; Figs. 8 & 9, pg. 12.
Note: A 2.2K EOL must be installed across terminals marked [TRIGGER] on MOM5 board or the unit
will remain in an alarm condition.
8. To trigger the unit using a supervised dry contact connect the 2.2K resistor in series for a [NC] trigger
input and in parallel for [NO] trigger input (Fig. 5, pg. 11).
9. Connect auxiliary devices triggered by the unit to the terminals marked [DRY OUTPUT NO & C] on
MOM5 board for normally open output or terminals marked [DRY OUTPUT NC & C] on MOM5 board
for normally closed output (Figs. 1 - 4, pgs. 6 - 9).
Note: This relay will energize when the unit is triggered.
10. For Access Control applications batteries are optional. When batteries are not used, a loss of AC will result
in the loss of output voltage. Batteries must be lead acid or gel type if used. Connect one (1) 12VDC battery
to terminals marked [+ BAT –] on power supply board for 12VDC operation (Figs. 1 - 4, pgs. 6 - 9).
Use two (2) 12VDC batteries connected in series for 24VDC operation. (Battery leads included).
11. Connect supervisory trouble reporting devices to outputs marked [AC FAIL, LOW BAT] and [Power Fail]
supervisory relay outputs marked [NO, C, NC] on power supply board (Figs. 1a - 4a, pgs. 6 - 9).
Use 22 AWG to 18 AWG for AC Fail & Low Battery reporting.
Note: When used in fire alarm, burglar alarm or access control applications, “AC Fail” relay should be
utilized to visually indicate that AC power is on.
To delay report for 6 hours cut “AC Delay” jumper (Figs. 1b - 4b, pgs. 6 - 9).
12. Please ensure that the cover is secured with the provided Key Lock.