MT319-401
User’s Guide
400-0698-001
6
13.
[SFT]
This command resets the card. It is the equivalent to
powering just the card off and on.
Command Format: [SFTCii]
Example:
Reset the card in slot by sending [SFTC4]. The card
responds with [RSTC04] indicating the card is resetting.
14.
[STA]
Enable/disable automatic feedback from the card. The
feedback format is the same as the [?Ci] command, but
only changes are reported.
Command Format: [STAxCii]
x
= On/off (x = 1 to enable, 0 disables)
Feedback Prefix Definitions:
MT Card Model Number
VR Firmware Revision
PR Card power consumption
HW Hardware enable
TP Card Temperature
15.
[TEMP]
This command returns the card temperature in Celsius.
Command Format: [TEMPCii]
Example:
Read the temperature of the card in slot 4 by sending
[TEMPC4]. The card responds with feedback:
[39C04]
16.
[VER]
Display the software version and card type for the card.
Command Format: [VERCii]
Example:
Send the command [VERC4] to check the version of the
MT319-401 in slot 4. The card returns feedback:
[690-0454-001C04]
690-0454-001 = firmware version
C04
= card ID
CEC Commands
The CEC commands in this section apply to the MT319-402
Rx. They are provided here for reference but have no effect on
the Rx HDMI output when sent to the MT319-401 Tx using the
MultiTasker network (TCP/IP or RS232).
These commands can be sent from the MT319-401 Tx but only
using the AV network interface using the [DB
(…)] command
shown later in this manual. CEC commands sent from an
MT319-401 Tx are executed by all Rx units on the same group.
17.
[TVx]
This command uses CEC commands to turn the TV
connected to an Rx unit on or off. When sent to a Tx unit
using the AV network command, all Rx units receiving
video from the Tx turn off.
MultiTasker Format:
[TVx]
AV Network Format:
[DB (TVx)]
x = 1 or 0 (1=on, 0=off)
Example:
Turn off the TV connected to Rx card in slot 4; [TV0C4].
18.
[TV1,x]
This command turns on the TV and selects the input
number provided.
MultiTasker Format:
[TV1,x]
AV Network Format:
[DB (TV1,x)]
x = TV input number (x = 1~9)
Example:
Turn on the TV connected to the Rx card in slot 4 and
switch to Input 2 on the TV by sending [TV1,2C4].
19.
[TV1,x,y,z]
This command is a configuration command for Rx units
only and executed when a card reset is executed, [SFT], or
at power up. Configure to turn on the TV and switch to a
known input on the TV. Set the delay time to wait in
seconds and the number of times to try and turn on the TV.
Not all TVs respond to CEC commands when AC power is
first applied. The delay is needed for some TVs to allow a
chance to be ready to accept CEC commands.
MultiTasker Format:
[TV1,x,y,z]
AV Network Format:
[DB (TV1,x,y,z)]
x = TV input number (x = 1~9)
y = Startup delay in seconds (y = 1~9)
z = Attempts (z = 1~9)
Example:
At power up, turn on the TV connected to the Rx card in
slot 4 and switch to Input 2. Wait 7 seconds before
attempting to turn on the TV. Make 3 attempts to turn on
the TV and switch to Input 2. This is done be sending the
following single command [TV1,2,7,3C4].
20.
[TV1,xx,xx,xx,xx]
This command allows a custom CEC command up to 4 hex
bytes. Multiple commands may be sent as needed.
xx = CEC hex code (advanced users only)
