manualshive.com logo in svg

Altera Ethernet Blaster Communications Cable, Руководство пользователя

Поделиться
Скачать
Altera Ethernet Blaster Communications Cable Скачать руководство пользователя страница 12

1–4

Chapter 1: About the EthernetBlaster Communications Cable

Cable Setup

EthernetBlaster Communications Cable User Guide

© June 2008

Altera Corporation

1

Refer to your operating system manual or contact your network administrator to 
verify that your network supports DHCP services and for instruction on how to 
change your IP address.

To maintain your computer’s IP address and change the EthernetBlaster 
communications cable’s default IP address, see 

“Configuring the 

EthernetBlaster Hardware to Use Static IP Addressing” on page 1–10

.

The EthernetBlaster communications cable includes a self-hosted administrative web 
page, allowing you to configure various aspects of cable operation. The following 
section describes how to access this web page based on your mode of connection.

Cable Setup

This section describes how to install and set up the EthernetBlaster communications 
cable for device configuration or programming including the following setups:

■

Remote Connection via Network Using Default Factory Settings

■

Direct Connection to a Computer Using Default Factory Settings

■

Configuring the EthernetBlaster Hardware to Use Static IP Addressing

■

Configuring the EthernetBlaster Hardware to Use Dynamic IP Addressing

■

Setting Up the EthernetBlaster Hardware in the Quartus II Software

■

Removing the EthernetBlaster Hardware from the Quartus II Software

1

For plug and header dimensions, pin names, and operating conditions, see 

“EthernetBlaster Communications Cable Specifications” on page 3–1

.

Remote Connection via Network Using Default Factory Settings

Use the following steps to connect remotely to the EthernetBlaster communications 
cable:

1

These steps assume no changes have been made to the default factory settings.

1. Disconnect the power cable from the circuit board.

2. Plug one end of a standard CAT 5 UTP 4-pair patch cable into the Ethernet jack on 

the EthernetBlaster communications cable, and the other end into a network port 
of a switch, router, or hub. See 

Figure 1–2

 below.

Содержание Ethernet Blaster Communications Cable




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды