background image

 
 

15 

 

 

Altai Technologies Ltd. All rights reserved 

 

Quick Setup Guide

 

Federal Communication Commission Interference Statement (FCC) – USA 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to 
Part  15  of  the  FCC  Rules.  These  limits  are  designed  to  provide  reasonable  protection  against  harmful 
interference  in  a  residential  installation.  This  equipment  generates,  uses  and  can  radiate  radio  frequency 
energy and, if not installed and used in accordance with the instructions, may cause harmful interference 
to  radio  communications.  However,  there  is  no  guarantee  that  interference  will  not  occur  in  a  particular 
installation. If this equipment does cause harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try to correct the interference 
by one of the following measures: 
 

 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect  the  equipment  into  an  outlet  on  a  circuit  different  from  that  to  which  the  receiver  is 
connected. 

 

Consult the dealer or an experienced radio/TV technician for help. 

 

 

FCC  Caution:  Any  changes  or  modifications  not  expressly  approved  by  the  party  responsible  for 
compliance could void the user's authority to operate this equipment. 
 
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) 
This device may not cause harmful interference, and (2) this device must accept any interference received, 
including interference that may cause undesired operation. 
 

 

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 
Operations in the 5.15-5.25GHz band are restricted to indoor usage only. 

 

 

IMPORTANT NOTE: 
FCC Radiation Exposure Statement: 

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled  environment. This 
equipment  should  be  installed  and  operated  with  minimum  distance  25cm  between  the  radiator  &  your 
body. 

 
European Conformity (CE) – EU 

This is a  Class B product. In a domestic environment, this product may cause radio interference,  in which 
case the user may be required to take adequate measures. 
 

 

 

Warning 

A2c may require professional installation depending on the deployment scenario. 
 
Only use the power adaptor supplied with A2c. Using a different power adaptor might damage A2c. 
 
 

Disclaimer 

All specifications are subject to change without prior notice. Altai Technologies assumes no responsibilities 
for  any  inaccuracies  in  this  document  or  for  any  obligation  to  update  information  in  this  document.  This 
document is provided for information purposes only. Altai Technologies reserves the right to change, modify, 
transfer, or otherwise revise this publication without notice. 

 

Содержание A2C

















Отзывы: