manualshive.com logo in svg

Alpine Opera Classic, Руководство по установке

Поделиться
Скачать
Alpine Opera Classic Скачать руководство пользователя страница 36

35

Eco/Classic Installation Guide and Technical Specification

7.3 

Checking the Initial Fault Safety

To check the safety equipment, proceed as follows:

The switching positions I and II are testing settings used only to check the safety during 
the annual inspection, or after repair work, or each time bed is put into service again. 

•  Setting switch position 4 (padlock symbol open      ).  Move all bed adjustments to a 

slightly raised position. 

•  Setting switch position 3 (padlock symbol closed      ).  When operating the 

adjustment buttons, no motorised adjustments should be possible.

•  Set switch on the back of the handset to testing position 1 (symbol I).
•  When operating the adjustment buttons, no motorised adjustments should be 

possible. 

•  Set switch on the back of the handset to testing position 2 (symbol II).
•  When operating the adjustment buttons, no motorised adjustments should be 

possible. 

 

Содержание Opera Classic

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды