manualshive.com logo in svg

Alpine Opera Classic, Руководство по установке

Поделиться
Скачать
Alpine Opera Classic Скачать руководство пользователя страница 33

32

Eco/Classic Installation Guide and Technical Specification

6.6 

Qualification of Users

The care bed must only be operated by persons who have the corresponding training or 
experience to enable them to handle the care bed correctly. 

6.5 

General Regulations

The care bed must only be used for the purpose intended. When setting up, operating, 
and using the care bed, respect the regulations in your country, the general recognised 
rules of technology, the occupational health and safety, and accident prevention 
regulations.

If the care bed is in a faulty state causing the patient/occupant, care personnel or third 
persons to be endangered, operation must not be started. 

7. Servicing

7.1 Principles

Operators of care beds are obliged according to the regulations in your country.

The test according to the regulation EN 62353 contains the following minimum 
requirements: 

•   Visual  check
•  Functional test 
•  Overall evaluation

To guarantee safe operation, a visual and functional test including an electrical test must 
be carried out at least once a year.  For this purpose, proceed according to the technical 
safety checklist as per regulation EN 62353

IMPORTANT

If you have any doubts about the safety or functioning of the bed or even a part of the bed as 
a result of the work performed below, the bed should under no circumstances be placed into 
service again. Contact the supplier or manufacturer in this case.

7.2 

List of Technical Safety Checks according to EN 62353

Care bed: Eco / Eco Low / Classic / Classic Low
Serial no: ………………………………
Location: ………………………….....
Person responsible: …………………………………………….
Inspected by: ……………………………………………..

Содержание Opera Classic

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды