22
-EN
System Setup Operation
1
Press and hold
SETUP
for at least 2 seconds.
The SETUP selection screen is displayed.
2
Touch
[
]
of System Setup.
The SYSTEM SETUP screen appears.
3
Touch
[
]
,
[
]
or
[
]
etc., of the desired item to
change its setting.
Setting items:
IN Int. Mute
*
1
/ IN Int. Icon / Remote Sensor
*
2
/ Camera IN /
NAV. IN / NAV. Mix
*
3
/ AUX IN / AUX OUT / Bluetooth IN /
USB Adapter / AUX+ IN / AUX+ Level
*
4
*
1
Displayed only when Bluetooth IN is OFF.
*
2
When ON is set in “Setting the Picture Output” (page 24), the item is
displayed.
*
3
When ON is set in “Setting the Navigation Mode” (page 23), the item
is displayed.
*
4
Not displayed when OFF is set in “Setting the AUX+ Mode”
(page 24).
4
Touch
[
]
to return to the previous screen.
Touch and hold
[
]
for at least 2 seconds to return to the
main source screen that was displayed before the setup
operation was started.
•
Immediately after changing the settings of System Mode (while the
system is writing data automatically) do not turn the ignition key
(engine key) to OFF. Otherwise, the settings may not be changed.
If an Alpine Ai-NET Interrupt Box (NVE-K200) is connected to the
unit, an Auxiliary Source will be allowed to interrupt the current audio
source. For example, you can listen to the voice guidance of your
navigation system when it occurs even while you are playing a song
stored in the USB memory. The song will be automatically muted
during voice guidance. For further details, please refer to the manual of
NVE-K200.
Setting item: IN Int. Mute
Setting contents: OFF / ON
•
The auxiliary device being connected must have an Interrupt wire
with a negative trigger for this function to operate automatically.
Otherwise, a separate switch needs to be added to switch it manually.
The unit can display the icon of an external device, such as a telephone,
whenever a phone call comes in to tell you there is a phone call.
Setting item: IN Int. Icon
Setting contents: INT / TEL
For optional remote control operation, the remote sensor of the external
device (monitor, etc.) can be switched, as you prefer.
Setting item: Remote Sensor
Setting contents: FRONT / REAR
•
If a touch screen monitor (connected to the Rear Monitor output
using the Monitor control lead) is touched, the command is executed
regardless of the remote control sensor setting. Note, however, that
the remote control sensor that has been set takes priority if it has
been 5 seconds since last touching the panel.
•
When an optional DVD changer is connected, and the remote control
sensor is set to REAR, some soft button operations
(
[
]
STOP, etc.) cannot be performed. In this case, set the remote
control sensor to FRONT.
System Setup
To display the System mode screen:
To watch a video source, your vehicle must be parked with the
ignition key in the ACC or ON position. To do this, follow the
procedure below.
1 Bring your vehicle to a complete stop at a safe
location. Engage the parking brake.
2 Keep pushing the foot brake and release the parking
brake once then engage it again.
3 When the parking brake is engaged for the second
time, release the foot brake.
•
For automatic transmission vehicles, place the transmission lever
in the Park position.
Now, the locking system for the System mode operation has been
released. Engaging the parking brake can reactivate the System
mode, as long as the car’s ignition has not been turned off. It is
not necessary to repeat the above procedure (1 through 3) of “To
display the System mode screen.”
Each time the ignition is turned OFF, perform the procedure of “To
display the System mode screen.”
The following steps 1 to 4 are common operations to each
“Setting item” of System Setup. Refer to each section for
details.
Setting the External Device Interrupt Mode
OFF:
The volume level can be adjusted in Interrupt mode.
ON:
Sound will not be output. The icon that is set in “Setting
the Interrupt Icon Display” is displayed.
Setting the Interrupt Icon Display
INT:
The INT icon appears on the display.
TEL:
When the external device (telephone) sends the interrupt
signal, the telephone icon appears on the display.
Switching the function of the remote
sensor
FRONT:
The remote sensor of this unit is effective.
REAR:
The remote sensor of the external monitor
connected to AUX OUT of this unit becomes
effective. The remote control operates the
source connected to the AUX OUT terminals.
Содержание IXA-W404 - 2-DIN 4.3" iPod Control Car Receiver
Страница 2: ......
Страница 65: ...63 EN List of World Clock For details see page 14 Information...
