30
-EN
Clock Display Setting
[Clock Display]
is selected on the General setup menu in step 3. Refer
to “General Setup Operation” (page 29).
The clock indication on the monitor display is turned on or off
respectively.
Setting item: Clock Display
Setting contents: Off / Type A (Initial setting) / Type B
Security Code Setting
[Security Code]
is selected on the General setup menu in step 3. Refer
to “General Setup Operation” (page 29).
You can set the system to be unusable without entering a password.
When you turn this setting to “On” and set a password, password input
is required when the system is connected to a battery and turned on for
the first time.
Setting item: Security Code
Setting contents: Off (Initial setting) / On
Setting the password
1
Touch [
] or [
] of “Security Code” to set to “On.”
2
After the confirmation message appears, touch
[OK]
.
The password setting screen is displayed.
3
Enter a password, then touch
[OK]
.
•
Enter the 6-digit number.
•
Input numbers are displayed as “
*
.”
4
Enter the same password again, then touch
[OK]
.
The password is set and the system returns to the previous
screen.
•
If you forget a registered password, you can not use this unit. In this
case, service will be required.
Clearing the password
1
Touch
[
]
or
[
]
of “Security Code” to set to “Off.”
The password setting screen is displayed.
2
Enter the password you have set, then touch
[OK]
.
The password is cleared and the system returns to the
previous screen.
•
Input numbers are displayed as “
*
.”
Setting Top banner and Bottom banner
Display
[Top/Bottom Banner Fade Out]
is selected on the General setup menu
in step 3. Refer to “General Setup Operation” (page 29).
You can configure the display setting for the Top banner and Bottom
banner for the audio/visual source.
Setting item: Top/Bottom Banner Fade Out
Setting contents: Off (Initial setting) / Top / Top and Bottom
Screen/LED Customize
[Screen/LED Customize]
is selected on the General setup menu in step
3. Refer to “General Setup Operation” (page 29).
The illumination control adjusts the brightness of the backlighting based
on the car ambient lighting for easier viewing.
Setting item: Dimmer
Setting contents: Auto (Initial setting) / On / Off
•
When “Auto” or “On” is set, the setting is also applied for the button
lighting in “Adjusting the Dimmer of Button Lighting at Night”
(page 30).
You can adjust the brightness of the backlight. This function could be
used, for instance, to change the screen brightness while travelling at
night.
Setting item: Screen Dimmer Level
Setting content: -15 to +15 (Initial setting: 0)
You can adjust the level between MIN (-15) and MAX (+15).
When it reaches the minimum or maximum point, the display
shows “MIN” or “MAX” respectively.
You can adjust the brightness of the button lighting at night with the
dimmer.
Setting item: Key Illumination Level
Setting level: -2 to +2 (Initial setting: 0)
Off:
Not displayed
Type A:
The clock indication is displayed in the upper right
corner of the screen when the Top banner fades out.
Type B:
The clock indication is always displayed in the
bottom right corner of the screen.
Setting Security code
Off:
Always displayed
Top:
Top banner will fade out after 5 seconds if no
operations are performed.
Top and Bottom:
Top banner and Bottom banner will fade out
after 5 seconds if no operations are
performed.
Setting the Brightness of the Backlighting
Auto:
Adjust the brightness of the background illumination of
the monitor automatically to the brightness of the car
interior.
On:
Keep the background illumination of the monitor dark.
Off:
Deactivate Auto Dimmer mode to keep the background
illumination of the monitor bright.
Adjusting the Minimum Level of Backlight
Adjusting the Dimmer of Button Lighting at
Night
Содержание INE-W990BT
Страница 97: ......
