background image

9

C048-781-30 R01, Rev. B (01/2020)

4.4  

4.4  Input Connections

Input Connections

WARNING! ELECTRICAL HAZARD

INPUTS MUST BE PROTECTED BY A LISTED 

CIRCUIT BREAKER OR BRANCH RATED FUSE. 

THE CIRCUIT BREAKER OR FUSE MUST 

BE RATED 375A MAX. MULTIPLE POWER 

SOURCES ARE PRESENT, ENSURE ALL 

INPUT POWER FEEDS ARE NOT ENERGIZED 

BEFORE INSTALLING THEM. ELECTRICAL 

INSTALLATION SHOULD ONLY BE PERFORMED 

BY QUALIFIED PERSONNEL WITH PROPER 

TOOLS AND PROTECTIVE SAFETY 

EQUIPMENT. FAILURE TO REINSTALL THE BUS 

SAFETY COVER WILL CREATE AN ELECTRICAL 

HAZARD.

MAKE SURE THAT ALL FEEDER CABLES HAVE 

HEAT SHRINK APPLIED PRIOR TO TERMINATION, 

AND THAT NO-OXIDE COMPOUND IS APPLIED TO 

ALL COPPER-TO-COPPER CONNECTIONS.

NOTICE

:

Table 3. 

Input Termination Specifications

TERMINATION 

TYPE

HOLE/

STUD 

SIZE

CENTER 

TO 

CENTER

RECOMMENDED 

TORQUE VALUE

Threaded Stud

3/8 in.

1 in.

18.75 ft∙lbs

 

Step 1. 

Flip up the plastic input safety cover to gain access to 

the HOT (-) and RTN (+) input bus termination 

locations.

Step 2. 

Install the RTN (+) cables/lugs to the threaded RTN (+) 

input studs as shown in Figure 5. Tighten hardware to 

250 in-lbs.

Step 3. 

Install the HOT (-) cables/lugs to the threaded HOT (-) 

input studs as shown in Figure 6. Tighten hardware to 

250 in-lbs.

Step 4. 

Reinstall the plastic input safety cover from Step 1.

Figure 5.  RTN Input Connections 

Figure 6.  HOT Input Connections

Содержание C016-2040-10



























Отзывы: