Alpha AWS-125 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 32

Alpha AWS-125 Скачать руководство пользователя страница 12

12

WARNING!

1. Before turning the switch ON, make sure the rotating parts are not touching

anything. If the switch is turned ON while they are in contact with anything
else, the blade may get damaged and it may cause injuries.

2. When a new blade is attached and the switch is turned ON, keep your body

well away from the exposed sides of the tool for a moment until the machine

reaches its full speed.

3. It is very dangerous to perform cutting operations using cracked, chipped or damaged

blades. Before starting cutting operations, keep the tool away from anyone nearby. Be
sure to perform a few test runs to check whether there are any abnormalities.

ABOUT DOUBLE INSULATION

This machine is designed with double insulation. Two insulations are used between the
conductor and the outer body of the machine. An Electric Machine with the double insulation
highly improves safety from electric shocks. Do not attach or replace unspeciﬁ ed parts and
do not assemble incorrectly. This may cause the insulation to malfunction.

LAWS AND REGULATIONS OF NOISE LEVELS

Please observe local laws and regulations regarding noise level in order to avoid disturbing
surrounding areas. Install a soundproof wall if required to comply with the local laws and
regulations.

INSTRUCTIONS FOR INSTALLING THE FELT STRIPS ON THE

AWS-125/AWS-225 BASE PLATE:

1.

Wipe base plate with a clean rag to remove any
dirt or residue.

2. Peel off film from the pressure sensitive

adhesive on the enclosed felt strips.

3.

Place strips on base plate parallel with the blade
and press into place.

Figure-5

«
...
10
11
12
13
14
...
»

Содержание AWS-125

































Отзывы:

Нет отзывов