background image

All brand names and product names are trademarks or registered trademarks of

their respective holders.

Microsoft does not make any representation or warranty regarding

specifications in this document or any product or item developed based on these

specifications.  Microsoft disclaims all express and implied warranties,

including but not limited to the implied warranties or merchantability, fitness

for a particular purpose and freedom from infringement.  Without limiting the

generality of the foregoing, Microsoft does not make any warranty of any kind

that any item developed based on these specification, or any portion of a

specification, will not infringe any copyright, patent, trade secret or other

intellectual property right of any person or entity in any country.  It is your

responsibility to seek licenses for such intellectual property rights where

appropriate.  Microsoft shall not be liable for any damages arising out of or in

connection with the use of these specifications, including liability for lost profit,

business interruption, or any other damages whatsoever.  Some states do not

allow the exclusion or limitation of liability or consequential or incidental

damages; the above limitation may not apply to you.

Microsoft, MS-DOS, Windows 3.x, Windows 95, Windows 98, and Windows

NT are registered trademarks of Microsoft Corporation.

Содержание UTA120
























































Отзывы: