Alpha Telecom UTA120 Скачать руководство пользователя страница 10

Страница: 10 / 55

Chapter 1: Introduction

UTA120 User’s Guide

PREINSTALLATION

To ensure a successful installation, we recommend that the installer prepare the
following items before proceeding.

Subscribe to ISDN from your telephone service provider

Refer to

Appendix A

for

a detailed explanation of ordering ISDN.

Select adequate communication software (HyperTerminal, Terminal, ProComm

Plus, etc.)

Note: For the operation and installation of the communication software, please refer to the

communication software manual.

If you want to use the AT Command Set with Windows 95/98/NT 4.0, then

HyperTerminal is the communications software supplied by Microsoft. (We

suggest using the Human to Machine Interface, or HMI, software instead of

the AT Command Set.)

For Windows 3.X, DOS, or UNIX, we recommend using a terminal program

and the AT Command Set to configure the UTA120.

Have your personal computer (PC) or workstation ready if you plan to use the

UTA120 for data communication.

Check the packing list. If something is missing, call your UTA120 vendor.

Be sure to register your UTA120 to validate your warranty.

INSTALLING THE HARDWARE

Warning: Always turn the UTA120 power off before connecting or disconnecting

cables.

Plug the DB9 cable into the UTA120’s DATA port. Insert the other end of the cable

into a communication port on the PC/workstation or other Data Terminal Equipment

(DTE).

Plug the RJ-11 cable into the UTA120’s U-Interface which is the protocol reference

point between ISDN network termination (NT1) equipment and the central office.

Insert the other end of the cable into the ISDN wall jack.

Plug the RJ-45 cable into the UTA120’s S/T-Interface. Insert the other end of the

cable into the ISDN S/T terminal equipment.

Plug another RJ-11 cable into the UTA120’s TEL1 and/or TEL2 port. Insert the

other end of the cable into any analog device (traditional telephone, modem, fax

machine or answering machine).

Plug the AC/DC power adapter into the POWER connector.

Secure the power adapter cord on the rear panel by using the attached hook on the

right side of the POWER connector.

Содержание UTA120























































Результаты поиска

Содержание UTA120

Отзывы:

Бренды по названию

Популярные бренды

Alpha Telecom UTA120, Руководство пользователя

Результаты поиска

Содержание UTA120

Отзывы:

Бренды по названию

Популярные бренды