Alpha Microsystems AM-6000 Скачать руководство пользователя

Страница: 91 / 110

Page

A-6

Appendix A

AM-6000 Computer Owner's Manual, Rev. 00

Workstation Connection Cables

For RJ-45 connectors, use the standard AM-359-50 cable set or straight RJ-45 patch cords. The
RJ-45 connectors use the same pin-outs as DB-9 connectors.

RS-232 pin assignments for connecting an IBM PC-compatible workstation to the Alpha Micro
computer are listed in the tables below.

Workstation Serial I/O
Port (Female DB-9)

Computer End Male

DB-9 Connector

SIGNAL

PIN#

DIRECTION

PIN#

SIGNAL

TXD

→

RTX

CTS

←

RTS

DSR

←

DCD

←

RXD

←

TXD

RTS

→

CTS

GND

←→

GND

Note: Pins 1, 6 and 8 on the workstation connector are jumpered together.

Table A-3: Pinouts for Workstation to Computer Cable - IBM PC/AT and Compatibles

Workstation Serial I/O
Port (Male DB-25)

Computer End Male

DB-9 Connector

SIGNAL

PIN#

DIRECTION

PIN#

SIGNAL

TXD

→

RTX

CTS

←

RTS

DSR

←

DCD

←

RXD

←

TXD

RTS

→

CTS

GND

←→

GND

Note: Pins 5, 6 and 8 on the workstation connector are jumpered together.

Table A-4: Pinouts for Workstation to Computer Cable - IBM PC/XT and Compatibles

Содержание AM-6000















































































































Результаты поиска

Содержание AM-6000

Отзывы:

Похожие инструкции для AM-6000

Бренды по названию

Популярные бренды

Alpha Microsystems AM-6000, Руководство пользователя

Результаты поиска

Содержание AM-6000

Отзывы:

Похожие инструкции для AM-6000

Бренды по названию

Популярные бренды