Alpha Microsystems AM-6000 Скачать руководство пользователя

Страница: 74 / 110

Page

7-6

Chapter Seven

AM-6000 Computer Owner's Manual, Rev. 00

D. If the computer did not boot successfully, try turn the computer off and back on again, following

these steps:

1. If your computer has a diskette drive, remove any diskette in the drive.

2. Turn off the power to any terminals, printers, and other peripheral devices connected to the

computer.

3. Turn off the computer and wait a few seconds.

4. Turn on all of the terminals, printers, and peripheral devices connected to the computer.

5. Turn on the computer. Do not hold in the reset button while you do so.

6. Return to Step C, above, to see if the computer is up and running.

Return to the current procedure or go to the next procedure on your checklist whether or not the
computer is up and running.

Procedure #4: Check Terminal/Printer

Various steps in the procedure below tell you to reset the computer. If you are not familiar with
this procedure, refer to Step B in "Procedure #3: Powerup/Reset."

A. Make sure each terminal is turned on:

1. For video display terminals, do you see anything on the screen? If so, the power is on—skip to

B, below.

For printers, is the power light on? If so, the power is on—skip to B, below.

2. See the terminal manufacturer's manual to find out how to troubleshoot power or fuse problems

for the device.

Correct the problem and reset the computer. If it comes up normally and your terminals seem to
work all right, your problem is fixed.

B. If you do not see anything on the screen, type

CTRL

, then

CTRL

. If you see ^C on the

screen, your computer is communicating with the terminal. Type:

SYSTAT

RETURN

If you see a system status display, your computer is probably up and running fine and your problem
is fixed.

C. Checking terminal cables:

1. Make sure the terminal cables are firmly connected to the correct ports. The terminal the

computer boots on is usually connected to Port #0.

2. Make sure the cables are firmly connected to the terminals. If a terminal has two ports, make

sure the cable is plugged into the correct one—usually labeled MAIN—not the AUX or
PRINTER port.

3. For printers, make sure the correct ends of the cable are attached to the computer and the

printer—cable ends are usually not interchangeable for printers.

Содержание AM-6000















































































































Результаты поиска

Содержание AM-6000

Отзывы:

Похожие инструкции для AM-6000

Бренды по названию

Популярные бренды

Alpha Microsystems AM-6000, Руководство пользователя

Результаты поиска

Содержание AM-6000

Отзывы:

Похожие инструкции для AM-6000

Бренды по названию

Популярные бренды