manualshive.com logo in svg

Allot NetEnforcer AC-2500 Series, Руководство по оборудованию, Страница: 54 / 87

Поделиться
Скачать
Allot NetEnforcer AC-2500 Series Скачать руководство пользователя страница 54

 

Chapter 3: Setting Up the NetEnforcer 

 

 

 

 

 

NetEnforcer AC-2500 Hardware Guide 

3-14 

Select whether you have a gateway defined in your network. If you select N then 
you will exit to the next step, skipping step 2-4. If you have a gateway select Y and 
proceed: 

2-4.Gateway: 

xxx.xxx.xxx.xxx 

(the current gateway definitions are displayed)

 

8.

 

Specify the IP address of the default gateway. Use the up and down arrow buttons to 
select the required number and the left and right arrow buttons to move between the 
digits. 

9.

 

Press the 

Enter

 button. The display area indicates the following: 

[S]ave/[C]ancel 

10.

 

Use the arrow buttons to select whether to save the settings or cancel and press the 

Enter

 button. The new IP and gateway settings are applied and after a few 

moments, the display area displays its default view, the current bandwidth 
consumption. 

The following cases of failure may be indicated: 

Failure

 

Display

Register NIC Settings 

Fail: NE IP save
Chk NE IP config

 

Netmask Save 

Fail: MASK save
Chk NE IP config

 

Management NIC Save 

Fail: Mgmt save
Chk NE IP config

 

Gateway Save 

Fail: GW save
Chk NE IP config

 

Содержание NetEnforcer AC-2500 Series
























































































Отзывы:

Нет отзывов