Allnet ALL69000 Скачать руководство пользователя страница 18

Страница: 18 / 148

Chapter 3: First Time Setup

Overview

Once the hardware is installed, physically connected to your network, and powered on, you
can configure the ALL69000 so that it is accessible to your network users. There are two ways
to set up your ALL69000: using the

ALLNET Setup Wizard

or the

LCD display

. Follow the

steps below for initial software setup.

ALLNET Setup Wizard

The handy ALLNET Setup Wizard makes configuring ALL69000 a snap. To configure the
ALL69000 using the Setup Wizard, perform the following steps:

1. Insert the installation CD into your CD-ROM drive (the host PC must be connected to

the network).

2. The Setup Wizard should launch automatically. If not, please browse your CD-ROM

drive and double click on

Setup.exe.

3. The Setup Wizard will start and automatically detect all ALLNET storage devices on

your network. If none are found, please check your connection and refer to

Chapter 7:

Troubleshooting

for assistance.

4. Select the ALL69000 that you like to configure.

NOTE

For MAC OS X users, double click on ALLNET Setup Wizard .dmg file.

Содержание ALL69000





















































































































































Результаты поиска

Содержание ALL69000

Отзывы:

Похожие инструкции для ALL69000

Бренды по названию

Популярные бренды

Allnet ALL69000, Руководство пользователя

Результаты поиска

Содержание ALL69000

Отзывы:

Похожие инструкции для ALL69000

Бренды по названию

Популярные бренды