Alligator 2788 MAS Скачать руководство пользователя страница 31

Страница: 31 / 31

-1-

FCC Statement

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired operation.

2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority

to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

The antenna(s) used for this transmitter must be fixed-mounted on outdoor permanent structures.

Содержание 2788 MAS




























Результаты поиска

Содержание 2788 MAS

Отзывы:

Похожие инструкции для 2788 MAS

Бренды по названию

Популярные бренды

Alligator 2788 MAS, Техническое руководство

Результаты поиска

Содержание 2788 MAS

Отзывы:

Похожие инструкции для 2788 MAS

Бренды по названию

Популярные бренды