Allied 92G1UH Скачать руководство пользователя страница 1

Страница: 1 / 57

506724-01

Page 1 of 57

Issue 1108

This manual must be left with the homeowner for future reference.

INSTALLATION INSTRUCTIONS

A95UH, A93UH, 95G1UH & 92G1UH

Warm Air Gas Furnace

Upflow/Horizontal Left and Right Air Discharge

This is a safety alert symbol and should never be ignored. When you see this symbol on labels or in

manuals, be alert to the potential for personal injury or death.

As with any mechanical equipment, personal injury can

result from contact with sharp sheet metal edges. Be

careful when you handle this equipment.

CAUTION

Improper installation, adjustment, alteration, service or

maintenance can cause property damage, personal injury

or loss of life. Installation and service must be performed

by a licensed professional installer (or equivalent), service

agency or the gas supplier.

WARNING

Manufactured By

Allied Air Enterprises, Inc.

A Lennox International, Inc. Company

215 Metropolitan Drive

West Columbia, SC 29170

Unit Dimensions ............................................................ 2

A95/A93/95G1/92G1UH Parts Arrangement ................ 3

A95/A93/95G1/92G1UH Gas Furnace ......................... 4

Shipping and Packing List ............................................ 4

Safety Information ......................................................... 4

Use of Furnace as a Construction Heater .................... 5

General ......................................................................... 6

Combustion, Dilution, Ventilation Air ............................. 6

Setting Equipment ........................................................ 9

Filters .......................................................................... 13

Duct System ................................................................ 13

Pipe and Fittings Specifications .................................. 13

Joint Cementing Procedure ........................................ 15

Venting Practices ........................................................ 16

TABLE OF CONTENTS

Vent Piping Guidelines ................................................ 17

Gas Piping .................................................................. 35

Electrical ..................................................................... 38

Unit Start Up ................................................................ 41

Gas Pressure Adjustment ........................................... 43

High Altitude Information ............................................. 43

Other Unit Adjustments ............................................... 46

Blower Motor Performance ......................................... 47

Service ........................................................................ 51

Planned Service .......................................................... 53

Diagnostic Codes ........................................................ 53

Repair Parts List ......................................................... 54

Start Up Checklist ....................................................... 55

(P) 506724-01

*P506724-01*

Содержание 92G1UH


























































Результаты поиска

Содержание 92G1UH

Отзывы:

Похожие инструкции для 92G1UH

Бренды по названию

Популярные бренды

Allied 92G1UH, Руководство по установке

Результаты поиска

Содержание 92G1UH

Отзывы:

Похожие инструкции для 92G1UH

Бренды по названию

Популярные бренды