background image

507651-01

Page 6  of  32

Issue 1907

Do not install the furnace in a corrosive or contaminated 

atmosphere.  Meet  all  combustion  and  ventilation  air 

requirements, as well as all local codes.

   CAUTION

All  gas  fired  appliances  require  air  for  the  combustion 

process.  If  sufficient  combustion  air  is  not  available,  the 

furnace  or  other  appliances  will  operate  inefficiently 

and  unsafely.  Enough  air  must  be  provided  to  meet  the 

needs of all fuel burning appliances and appliances such 

as exhaust fans which force air out of the house. When 

fireplaces, exhaust fans, or clothes dryers are used at the 

same time as the furnace, much more air is necessary to 

ensure  proper  combustion  and  to  prevent  a  downdraft. 

Insufficient  air  causes  incomplete  combustion  which  can 

result in carbon monoxide.

In addition to providing combustion air, fresh outdoor air 

dilutes contaminants in the indoor air. These contaminants 

may  include  bleaches,  adhesives,  detergents,  solvents 

and  other  contaminants  which  can  corrode  furnace 

components.

The  requirements  for  providing  air  for  combustion  and 

ventilation  depend  largely  on  whether  the  furnace  is 

installed in an unconfined or a confined space.

Unconfined Space

An  unconfined  space  is  an  area  such  as  a  basement 

or  large  equipment  room  with  a  volume  greater  than  50 

cubic feet (1.42 m3) per 1,000 Btu (.29 kW) per hour of 

the combined input rating of all appliances installed in that 

space. This space also includes adjacent rooms which are 

not separated by a door. Though an area may appear to 

be unconfined, it might be necessary to bring in outdoor air 

for combustion if the structure does not provide enough air 

by infiltration. If the furnace is located in a building of tight 

construction  with  weather  stripping  and  caulking  around 

the  windows  and  doors,  follow  the  procedures  in  the  air 

from outside section.

Confined Space

A confined space is an area with a volume less than 50 

cubic feet (1.42 m3) per 1,000 Btu (.29 kW) per hour of 

the combined input rating of all appliances installed in that 

space.  This  definition  includes  furnace  closets  or  small 

equipment rooms.

When the furnace is installed so that supply ducts carry 

air  circulated  by  the  furnace  to  areas  outside  the  space 

containing the furnace, the return air must be handled by 

ducts which are sealed to the furnace casing and which 

terminate outside the space containing the furnace. This 

is  especially  important  when  the  furnace  is  mounted  on 

a platform in a confined space such as a closet or small 

equipment room. Even a small leak around the base of the 

unit at the platform or at the return air duct connection can 

cause a potentially dangerous negative pressure condition. 

Air for combustion and ventilation can be brought into the 

confined  space  either  from  inside  the  building  or  from 

outside.

Figure 2. 

Equipment in Confined Space - All Air from 

Inside

NOTE: 

Each opening shall have a free area of at least one square 

inch per 1,000 Btu (645 mm² per .29 kW) per hour of the total 

input rating of all equipment in the enclosure, but not less than 100 

square inches (64546 mm²).

Air from Inside

If  the  confined  space  that  houses  the  furnace  adjoins  a 

space  categorized  as  unconfined,  air  can  be  brought  in 

by  providing  two  permanent  openings  between  the  two 

spaces. Each opening must have a minimum free area of 1 

square inch (645 mm2) per 1,000 Btu (.29 kW) per hour of 

total input rating of all gas fired equipment in the confined 

space. Each opening must be at least 100 square inches 

(64516 mm2). One opening shall be within 12 inches (305 

mm) of the top of the enclosure and one opening within 12 

inches (305 mm) of the bottom. See Figure 2.

Air from Outside

If  air  from  outside  is  brought  in  for  combustion  and 

ventilation, the confined space must have two permanent 

openings.  One  opening  shall  be  within  12  inches  (305 

mm) of the top of the enclosure and one opening within 

12 inches (305 mm) of the bottom. These openings must 

communicate  directly  or  by  ducts  with  the  outdoors  or 

spaces  (crawl  or  attic)  that  freely  communicate  with  the 

outdoors or indirectly through vertical ducts. Each opening 

shall have a minimum free area of 1 square inch (645 mm2) 

Содержание 80G1UHEX Series

































Отзывы: