background image

507651-01

Issue 1907

Page 5  of  32

General

These instructions are intended as a general guide and do 

not supersede local codes in any way. Consult authorities 

having jurisdiction before installation.

In  addition  to  the  requirements  outlined  previously,  the 

following  general  recommendations  must  be  considered 

when installing one of these furnaces:

• 

Place  the  furnace  as  close  to  the  center  of  the  air 

distribution  system  as  possible.  The  furnace  should 

also be located close to the chimney or vent termination 

point.

• 

Do  not  install  the  furnace  where  drafts  might  blow 

directly into it. This could cause improper combustion 

and unsafe operation.

• 

Do not block the furnace combustion air openings with 

clothing,  boxes,  doors,  etc. Air  is  needed  for  proper 

combustion and safe unit operation.

• 

When  the  furnace  is  installed  in  an  attic  or  other 

insulated  space,  keep  insulation  away  from  the 

furnace.

• 

Please  consult  the  manufacturer  of  your  evaporator 

coil  for  their  recommendations  on  distance  required 

between  the  heat  exchanger  and  their  drain  pan. 

Adequate space must be provided between the drain 

pan and the furnace heat exchanger.

Combustion, Dilution & Ventilation Air

In the past, there was no problem in bringing in sufficient 

outdoor air for combustion. Infiltration provided all the air 

that  was  needed.  In  today’s  homes,  tight  construction 

practices  make  it  necessary  to  bring  in  air  from  outside 

for  combustion.  Take  into  account  that  exhaust  fans, 

appliance vents, chimneys, and fireplaces force additional 

air  that  could  be  used  for  combustion  out  of  the  house. 

Unless outside air is brought into the house for combustion, 

negative pressure (outside pressure is greater than inside 

pressure) will build to the point that a downdraft can occur 

in the furnace vent pipe or chimney. As a result, combustion 

gases  enter  the  living  space  creating  a  potentially 

dangerous situation.

In the absence of local codes concerning air for combustion 

and ventilation, use the guidelines and procedures in this 

section  to  install  these  furnaces  to  ensure  efficient  and 

safe operation. You must consider combustion air needs 

and requirements for exhaust vents and gas piping.

A  portion  of  this  information  has  been  reprinted 

with  permission  from  the  National  Fuel  Gas  Code 

(ANSI-Z223.1). This reprinted material is not the complete 

and official position of the ANSI on the referenced subject, 

which is represented only by the standard in its entirety.

Insufficient  combustion  air  can  cause  headaches, 

nausea,  dizziness  or  asphyxiation.  It  will  also  cause 

excess water in the heat exchanger resulting in rusting 

and  premature  heat  exchanger  failure.  Excessive 

exposure  to  contaminated  combustion  air  will  result 

in  safety  and  performance  related  problems.  Avoid 

exposure to the following substances in the combustion 

air supply:

• 

Permanent wave solutions

• 

Chlorinated waxes and cleaners

• 

Chlorine base swimming pool chemicals

• 

Water softening chemicals

• 

De-icing salts or chemicals

• 

Carbon tetrachloride

• 

Halogen type refrigerants

• 

Cleaning solvents (such as perchloroethylene)

• 

Printing inks, paint removers, varnishes, etc.

• 

Hydrochloric acid

• 

Anti-static fabric softeners for clothes dryers

• 

Masonry acid washing materials

   WARNING

NOTWITHSTANDING  THE  FOREGOING,  INSTALLER 

IS  RESPONSIBLE  FOR  CONFIRMING THAT THE  USE 

OF  CONSTRUCTION  HEAT  IS  CONSISTENT  WITH 

THE  POLICIES  AND  CODES  OF  ALL  REGULATING 

ENTITIES. ALL SUCH POLICIES AND CODES MUST BE 

ADHERED TO.

Содержание 80G1UHEX Series

































Отзывы: