Allied 80G1UHEX Series Скачать руководство пользователя

Страница: 3 / 32

507651-01

Issue 1907

Page 3 of 32

A80UH1EX & 80G1UHEX Gas Furnace

The

A80UH1EX & 80G1UHEX

unit is shipped ready for

installation in the upflow or horizontal position fueled by

natural gas. The furnace is shipped with the bottom panel

in place. The bottom panel must be removed if the unit is

to be installed in a horizontal application. The panel may

also be removed in upflow applications.

This furnace

is approved for installations from 0 - 4500 ft. Do not

install in high altitude applications.

Shipping & Packing List

1 - Assembled Gas Furnace
1 - Bag assembly containing the following:

2 - Screws
1 - Snap bushing
1 - Snap plug
1 - Wire tie
1 -Vent warning label
1 - Owner’s manual and warranty card

Check equipment for shipping damage. If you find any

damage, immediately contact the last carrier.

Please refer to specification sheets for available

accessories.

Safety Information

Improper installation, adjustment, alteration, service

or maintenance can cause property damage, personal

injury or loss of life. Installation and service must be

performed by a licensed professional installer (or

equivalent), service agency or the gas supplier.

WARNING

As with any mechanical equipment, personal injury can

result from contact with sharp sheet metal edges. Be

careful when you handle this equipment.

CAUTION

Certifications

These units are CSA International certified to ANSI Z21.47.

In the USA, installation of gas furnaces must conform with

local building codes. In the absence of local codes, units

must be installed according to the current National Fuel

Gas Code (ANSI-Z223.1). The National Fuel Gas Code is

available from the following address:

American National Standards Institute, Inc.

11 West 42nd Street

New York, NY 10036

Clearances

Adequate clearance must be made around the air openings

into the vestibule area. In order to ensure proper unit

operation, combustion and ventilation air supply must be

provided according to the current National Fuel Gas Code.

Vent installations must be consistent with the venting

tables (in this instruction) and applicable provisions of local

building codes.

This furnace is CSA International certified for installation

clearances to combustible material as listed on the unit

nameplate and in the tables in Figure 7 and Figure 12.

Accessibility and service clearances must take precedence

over fire protection clearances.

NOTE:

For installation on combustible floors, the furnace

shall not be installed directly on carpeting, tile, or other

combustible material other than wood flooring.

Installed Locations

For installation in a residential garage, the furnace must be

installed so that the burner(s) and the ignition source are

located no less than 18 inches (457 mm) above the floor.

The furnace must be located or protected to avoid physical

damage by vehicles. When a furnace is installed in a public

garage, hangar, or other building that has a hazardous

atmosphere, the furnace must be installed according to

recommended good practice requirements and current

National Fuel Gas Code.

Temperature Rise

NOTE:

Furnace must be adjusted to obtain a temperature

rise within the range specified on the unit nameplate.

Failure to do so may cause erratic limit operation and may

result in premature heat exchanger failure.

This furnace must be installed so that its electrical

components are protected from water.

The A80UH1EX & 80G1UHEX is approved for natural

gas only. Do not attempt to convert and or install in LP

propane applications.

IMPORTANT

Содержание 80G1UHEX Series

































Результаты поиска

Содержание 80G1UHEX Series

Отзывы:

Похожие инструкции для 80G1UHEX Series

Бренды по названию

Популярные бренды

Allied 80G1UHEX Series, Руководство по установке

Результаты поиска

Содержание 80G1UHEX Series

Отзывы:

Похожие инструкции для 80G1UHEX Series

Бренды по названию

Популярные бренды