Allied 300 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 66

Allied 300 Скачать руководство пользователя страница 30

Allied Construction Products, LLC Technical Manual Ho-Pac 300, 300B & 500, 500B

19

SECTION 7.0

INSTALLATION & REMOVAL

7.1 Carrier Compatibility

Ho-Pac models 300, 300B, 500 & 500B, are
designed to fit small excavators. Attach the
compactor only to carriers having adequate
load-carrying capabilities. Carrier weight
ranges, listed in Section 5.1, are intended
as a guideline. Factors such as stick length,
counterweights, undercarriage, etc., affect
the carrier’s lifting capacity and must be
taken into consideration prior to mounting
the compactor. Always adhere to the safe
working load established by the carrier
manufacturer to assure stable carrier
operation.

The hydraulic power needed to operate the
Ho-

Pac is provided by the carrier’s hydraulic

system. If the carrier is not equipped with an
auxiliary circuit, contact Allied for an
installation kit. Follow the installation
instructions provided with the hydraulic kit.

7.2 Testing and Adjusting

IMPORTANT

Do not operate the Ho-Pac beyond its
performance limits. Exceeding the
specifications listed in Section 5.1 can be
dangerous to the operator and result in
expensive repair costs.

Precautions must be taken before using the
Ho-Pac to ensure the compactor is not
damaged. Before the Ho-Pac is used on a
carrier for the first time, the auxiliary circuit
must be tested and, if necessary, adjusted.
By following these steps, the Ho-Pac will
provide efficient operation, production rates
and dependable service life.

Prior to mounting the Ho-Pac, test the
carrier’s hydraulic circuit. Measure the
oil flow and pressure.

Use a flow meter that has been
calibrated to obtain accurate flow
measurements of the carrier’s auxiliary
circuit.

Compare your test results with the
specifications in Section 5.1.

Optimal performance is achieved only
when the oil flow from the carrier is
properly matched to the size of the
motor installed on the compactor.

Identify which motor and valve package
option is installed on the Ho-Pac before
any adjustments are made. Refer to
Section 12 for information on motor and
valve identification.

Record the results of your flow and
pressure measurements in the spaces
provided on the Warranty Registration
Form.

7.3 Installation on to Carrier

7.3.1 Tools Required to Attach the
Ho-Pac

No special tools are required, but the
following tools should be available:

  Safety eyewear & gloves
  Sledge Hammer
  Drift pin
  3/4 drive socket wrench
  3/4 drive metric sockets
  Grease gun
  Standard & Metric open end wrenches
  Pry bar

Rags

The Ho-Pac is attached to the carrier in the
same manner as mounting a bucket. Use
standard mechanic’s techniques and tools

«
...
28
29
30
31
32
...
»

Содержание 300



































































Отзывы:

Нет отзывов