Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 49 / 214

x930 Series Installation Guide for Virtual Chassis Stacking

Switch ID LED

The Switch ID LED, shown in Figure 12, displays the ID number of the

switch. A stand-alone switch has the ID number 0. Switches in a VCStack

have the numbers 1 to 8.

Figure 12. Switch ID LED

Table 11. Stacking Port LEDs

LED

State

Description

Link/Activity

Off

The port is empty, the stacking

transceiver has not established a link to a

network device, or the LEDs are turned

off. To turn on the LEDs, use the eco-

friendly button.

Solid green

The stacking transceiver has established

a 10Gbps link to another switch in the

stack.

Flashing

green

The stacking transceiver is receiving or

transmitting packets.

Solid amber The stacking transceiver in the port has

established a link at 1Gbps to a network

device.

Flashing

amber

The stacking transceiver is receiving or

transmitting packets to a network device

at 1Gbps.

Switch ID LED

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды