Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 44 / 214

Chapter 1: Overview

The copper ports on the AT-x930-28GPX and AT-x930-52GPX Switches

have two LEDs that display link, activity and PoE information. The LEDs

are shown in Figure 9 on page 45.

Note

You can view the duplex mode information for the ports on the AT-

x930-28GPX and AT-x930-52GPX Switches with the management

software.

Table 7. LEDs on the 10/100/1000Base-T Ports on the AT-x930-28GTX,

AT-x930-28GSTX and AT-x930-52GTX Switches

LED

State

Description

Link/

Activity

LED

Solid Green A port has established a 1000 Mbps link to

a network device.

Flashing

Green

A port is transmitting or receiving data at

1000 Mbps.

Solid Amber A port has established a 10 or 100 Mbps

link to a network device.

Flashing

Amber

A port is transmitting or receiving data at 10

or 100 Mbps.

Off

A port has not established a link with

another network device or the LEDs are

turned off. To turn on the LEDs, use the

eco-friendly button.

Duplex

Mode

LED

Green

A port is operating in full duplex mode.

Amber

A port is operating in half-duplex mode at 10

or 100 Mbps. (Half-duplex mode does not

apply to 1000 Mbps operation.)

Flashing

Amber

Collisions are occurring on a port operating

at 10 or 100 Mbps.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды