Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 45 / 214

x930 Series Installation Guide for Virtual Chassis Stacking

Figure 9. LEDs for the 10/100/1000Base-T Ports on the AT-x930-28GPX

and AT-x930-52GPX Switches

The LEDs are described in Table 8.

Table 8. LEDs on the 10/100/1000Base-T Ports on the AT-x930-28GPX

and AT-x930-52GPX Switches

LED

State

Description

Link/

Activity

LED

Solid Green A port has established a 1000 Mbps link to

a network device.

Flashing

Green

A port is transmitting or receiving data at

1000 Mbps.

Solid Amber A port has established a 10 or 100 Mbps

link to a network device.

Flashing

Amber

A port is transmitting or receiving data at 10

or 100 Mbps.

Off

A port has not established a link with

another network device or the LEDs are

turned off. To turn on the LEDs, use the

eco-friendly button.

Link/Activity

LED

PoE

LED

PoE

LED

Link/Activity

LED

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды