Allied Telesis AT-x930-28GPX Скачать руководство пользователя страница 113

Страница: 113 / 214

113

Chapter 6

Installing the Switch on a Table

To install the switch on a table, perform the following procedure:

Warning

Switches should not be stacked on a table or desktop because that

could present a personal safety hazard if you need to move or

replace units.



E91

Warning

The switch is heavy. Always ask for assistance when moving or

lifting the device so as to avoid injuring yourself or damaging the

equipment.

1. Review the procedure in “Choosing a Site for the Switch” on page 89 to

verify that the selected site is suitable for the unit.

2. Check to be sure that the table or desk is strong enough to support the

weight of the switch.

3. Check to be sure that all of the appropriate components are included in

the shipping container. Refer to “Unpacking the Switch” on page 90.

4. Place the switch upside down on a level, secure table or desk.

5. Install the seven bumper feet to the bottom of the switch. Refer to

Figure 52.

Three bumper feet should be installed along the front edge of the

bottom panel and four feet along the rear edge.

Figure 52. Installing the Bumper Feet

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды