Allied Telesis AT-x930-28GPX Скачать руководство пользователя страница 89

Страница: 89 / 214

x930 Series Installation Guide for Virtual Chassis Stacking

Choosing a Site for the Switch

Observe these requirements when planning the installation of the switch.



If you plan to install the switch in an equipment rack, check to be

sure that the rack is safely secured so that it will not tip over.

Devices in a rack should be installed starting at the bottom, with

the heavier devices near the bottom of the rack.



If you plan to install the switch on a table, check to be sure that the

table is level and stable.



The power outlet should be located near the switch and be easily

accessible.



The site should allow for easy access to the ports on the front of

the switch, so that you can easily connect and disconnect cables,

and view the port LEDs.



The site should allow for adequate air flow around the unit and

through the cooling vents on the front and rear panels. (The

ventilation direction in units that have a cooling fan is from front to

back, with the fan on the back panel drawing the air out of the unit.)



The site should not expose the switch to moisture or water.



The site should be a dust-free environment.



The site should include dedicated power circuits or power

conditioners to supply reliable electrical power to the network

devices.



Do not install the switch in a wiring or utility box because it will

overheat and fail from inadequate airflow.

Warning

Switches should not be stacked on a table or desktop because that

could present a personal safety hazard if you need to move or

replace switches.



E91

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды